23/06/2022 13:09:14

Retractor - Seatbelt - 2nd Row - LH (6 Seat) (Remove and Replace)

Correction code 20056102 2.04 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open all the doors and lower the front windows.
  2. Remove the driver seat from the vehicle. See Seat Assembly - 1st Row - LH (Remove and Install).
  3. Remove the underbelly trim. See Trim - Underbelly - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
  4. Remove the LH 2nd row seatbelt anchor escutcheon. See Escutcheon - Seatbelt Anchor - 2nd Row - LH (6 Seat) (Remove and Replace).
  5. Remove the LH 2nd row seat back cover. See Cover - Seat Back - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the easy entry switch from the seat back cover.
  6. Remove the LH 2nd row seatbelt escutcheon. See Escutcheon - Seatbelt - 2nd Row - LH (6 Seat) (Remove and Replace).
  7. Route the LH 2nd row seatbelt through the lower and upper cushions, and then remove the seat back assembly.
  8. Remove the screws (x6) that attach the head rest bracket to the seat assembly.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • PH2 screwdriver
  9. Disconnect the LH 2nd row seatbelt assembly electrical connector.
  10. Remove the zip tie that attaches the LH 2nd row seat harness to the seatbelt assembly.
  11. Remove the bolt that attaches the LH 2nd row seatbelt assembly to the seat frame.
    50 Nm (36.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T45 socket
  12. Maneuver the LH 2nd row seatbelt assembly through the seat back, and then remove the assembly from the seat back.

Install

  1. Position the LH 2nd row seatbelt assembly onto the seat back, and then maneuver the seat buckle through the seat back to install it into the seat.
  2. Install the bolt that attaches the LH 2nd row seatbelt assembly to the seat frame.
    50 Nm (36.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T45 socket
  3. Install a zip tie that attaches the LH 2nd row seat harness to the seatbelt assembly.
  4. Connect the LH 2nd row seatbelt assembly electrical connector.
  5. Position the head rest bracket into the seat assembly, and then install the screws (x6) that attach the bracket to the seat.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • PH2 screwdriver
  6. Feed the LH 2nd row seatbelt through LH 2nd row seatbelt anchor escutcheon, and then route the seat belt harness through the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not install the seat belt anchor escutcheon to the seat assembly at this time.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the seat belt anchor escutcheon is routed onto the seat belt prior to seat belt anchor being routed through seat cushion.
  7. Install the LH 2nd row seatbelt escutcheon. See Escutcheon - Seatbelt - 2nd Row - LH (6 Seat) (Remove and Replace).
  8. Install the LH 2nd row seat back cover. See Cover - Seat Back - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
  9. Position the LH 2nd row seatbelt anchor escutcheon into the seat cushion, and then secure the tabs (X4) that attach the escutcheon to the seat cushion.
    Informational PurposesAn informational icon, calling your attention
    Note
    Firmly press the seat belt anchor escutcheon to the seat cushion to secure it.
  10. Install the bolt and new nut that attach the LH 2nd row seat belt anchor to the seat frame.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Reuse the seat frame washer from removal.
    Tip: Use of the following tool(s) is recommended:
    • Torx T45 socket
    • 11/16 combination wrench
    Informational PurposesAn informational icon, calling your attention
    Note
  11. Install the underbelly trim. See Trim - Underbelly - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
  12. Install the driver seat into the vehicle. See Seat Assembly - 1st Row - LH (Remove and Install).
  13. Raise the front windows and close the LH front door.