20/09/2022 14:51:18

Escutcheon - Seatbelt - 3rd Row - LH (Remove and Replace)

Correction code 20059102 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH falcon wing doors.
  2. Open the liftgate.
  3. Fold the 2nd row 40 and 60 seats downward.
  4. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  5. Remove the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  6. Remove the rear trunk carpet. See Carpet - Rear Trunk (7 Seat) (Remove and Replace).
  7. Fold the LH and RH 3rd row seat backs downward.
  8. Remove the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
  9. Release the tabs (x4), fir tree clips (x2), and J hook that attach the lower section of the LH 3rd row seat upholstery to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the tabs inward, and then upwards to release.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  10. Unfold the LH 3rd row seat to original position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Leave the seat headrest in the folded position.
  11. Release the J-hook clip that attaches the upper half of the LH 3rd row seat upholstery to the seat.
  12. From the 3rd row, pull the top outer portion of the seat cover and foam outward to gain access to the LH 3rd row seat belt escutcheon.
  13. Carefully pull the LH 3rd row seat belt escutcheon forward to expose the switch connector, and then disconnect the connector.
  14. Release the clips (x4) that attach the LH 3rd row seat belt escutcheon to the seat cushion trim, and then remove the escutcheon from the seat belt.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in

Install

  1. Position the LH 3rd row seat belt escutcheon on the seat belt, and then install the clips (x4) that attach the escutcheon to the seat cushion trim.
  2. Connect the LH 3rd row seat belt escutcheon switch connector.
  3. From the 3rd row, fold back the top outer portion of the seat cover and foam over the seat frame.
  4. Engage the J hook clip that attaches the upper half of LH 3rd row seat upholstery to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the seat to a workable position, start at one end of the J hook clip, and then fold the clip inwards until the other end of the upholstery is fully tucked.
  5. Engage the tabs (x4), fir tree clips (x2), and J hook that attach the lower section of the LH 3rd row seat upholstery to the seat.
  6. Install the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
  7. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  8. Install the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
  9. Install the rear trunk carpet. See Carpet - Rear Trunk (7 Seat) (Remove and Replace).
  10. Unfold the LH and RH 3rd row seat backs into original position.
  11. Close the liftgate.
  12. Unfold the 2nd row 40 and 60 seats into original position.
  13. Close the LH and RH falcon wing doors.