2023-08-30

Link - Stabilizer Bar - Front - LH (Remove and Replace)

Correction code 31012002 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Suspension - Front (Torque)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nut that attaches the stabilizer bar end link to the knuckle
70 Nm (51.6 lbs-ft)
  • 15 mm socket
  • 5 mm hex
Replace PN - 1111542-00-A
Nut that attaches the stabilizer bar end link to the stabilizer bar
70 Nm (51.6 lbs-ft)
  • 15 mm combination wrench
  • 5 mm hex
Replace PN - 1659754-00-A

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  2. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  3. Remove and discard the nut that attaches the LH front stabilizer bar end link to stabilizer bar, then rotate the end link to the side.
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter hold the stud with a 5mm hex socket and use the wrench to remove the nut.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Move the stabilizer bar assembly up and down as need to remove the end link.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm combination wrench
    • 5 mm hex
  4. Remove and discard the nut that attaches the front stabilizer bar end link to the LH front knuckle, and then remove the link from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter hold the stud with a 5mm hex socket and use the wrench to remove the nut.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
    • 5 mm hex

Install

  1. Position the LH front stabilizer bar link to the knuckle, and then install a new nut that attaches the link to the knuckle.
    70 Nm (51.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use a 5mm hex tool to keep the stud from spinning.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
    • 5 mm hex
  2. Position the LH front stabilizer bar link to the stabilizer bar, and then install a new nut that attaches the link to the stabilizer bar.
    70 Nm (51.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter hold the stud with a 5mm hex socket and use the wrench.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Move the stabilizer bar assembly up and down as need to align the end link.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm combination wrench
    • 5 mm hex
  3. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  4. Remove the vehicle from the lift. See Raise Vehicle - 2 Post Lift.