08/09/2022 16:26:02

Glove Box (Remove and Replace)

Correction code 14051002 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the front doors and lower the front windows.
  2. Move front passenger seat rearward.
  3. Remove the front passenger floor mat.
  4. Remove the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace)
  5. Remove the RH center console side carpet. See Carpet - Side Panel - Center Console - LH (Remove and Replace).
  6. Remove the RH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  7. Remove the RH IP end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  8. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  9. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  10. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  11. Disconnect LV power. See LV Power (Disconnect and Connect).
  12. Remove the instrument panel service panel. See Service Panel - Instrument Panel (Remove and Replace)
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the cabin temperature sensor fan from the service panel.
  13. Remove the touchscreen assembly. See Touchscreen (HW3) (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the display mechanism from the touchscreen after the assembly has been removed from the instrument panel.
  14. Remove the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  15. Remove the front passenger knee airbag assembly. See Knee Airbag - Front Passenger (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the components from the knee airbag assembly after the assembly has been removed from the IP.
  16. Remove the screws (x5) that attach the glove box to the vehicle, and then release the glove box from the instrument panel.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  17. Disconnect the glove box electrical connectors (x3).
  18. Remove the screws (x2) and release the clip that attach the USB outlet to the glove box assembly, and then remove the outlet from the assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  19. Remove the glove box from the vehicle.

Install

  1. Position the USB outlet into the glove box assembly, and then install the screws (x2) and secure the clip that attach the outlet to the glove box assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the USB socket is flush in the glove box.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  2. Connect the glove box electrical connectors (x3), and then route the harness through the glove box datums.
  3. Install the screws (x5) that attach the glove box to the vehicle.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  4. Install the front passenger knee airbag assembly. See Knee Airbag - Front Passenger (Remove and Replace).
  5. Install the RH center console side carpet. See Carpet - Side Panel - Center Console - LH (Remove and Replace).
  6. Install the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace)
  7. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  8. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  9. Install the RH IP end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  10. Install the RH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  11. Install the front passenger floor mat.
  12. Install the instrument panel RH middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  13. Position the instrument panel closeout panel to the instrument panel, and then secure the tabs (x4) that attach the closeout panel to the instrument panel.
  14. Install the touchscreen assembly. See Touchscreen (HW3) (Remove and Replace).
  15. Install the instrument panel service panel. See Service Panel - Instrument Panel (Remove and Replace)
  16. Connect LV power. See LV Power (Disconnect and Connect).
  17. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  18. Move the front passenger seat to the original position.
  19. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors
  20. Raise the front windows and close the LH front door.
  21. Close LH front door