26/09/2024 12:59:34

Window Motor/Regulator Assembly - Front - LH (Remove and Replace)

Correction code 11502002 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH front door and lower the front windows.
  2. Remove the LH front door trim decor. See Decor - Trim - Front Door - LH (Remove and Replace).
  3. Remove the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace).
  4. Remove the bolts (x4) that attach the LH front door controller module backing plate to the module, and then remove the plate from the module.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
  5. Connect a window master switch to the LH front door harness, and then raise the window fully.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect door panel x927 if the switch kit is not available.
  6. Apply masking tape to window and outer belt molding, mark the glass position, and then break the tape between the glass and molding.
  7. Remove the butyl patch that covers the access hole for the rear window regulator nut.
  8. Loosen the nut that attaches the rear of the window glass to the regulator.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The nut does not need to be fully removed.
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  9. Use the window master switch to fully lower the LH front window, and then disconnect switch.
  10. Remove the LH front door outer belt seal . See Seal - Outer Belt - Front Door - LH (Remove and Replace).
  11. Raise the regulator for access to the front clip on the LH front window motor/regulator assembly.
  12. Release the front clip on the LH front window motor/regulator assembly, and then remove the LH front door glass from the door assembly.
  13. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  14. Disconnect LV power. See LV Power (Disconnect and Connect).
  15. Release the locking tab, and then disconnect the LH door pressure sensor connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not push down on the red tab. Pull the red tab to disengage lock, and then pull again to release the connector.
  16. Remove the LH front door closeout panel. See Closeout Panel - Door - Front - LH (Remove and Replace).
  17. Disconnect the LH front door cinch motor connector.
  18. Disconnect the LH front window motor.
  19. Remove the nuts (x2)that attach the front section of the LH front door window regulator to the door.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  20. Remove the nuts (x2) that attach the rear section of the LH front window regulator to the door.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  21. Remove the screws (x3) that attach the LH front window motor to the door.
    1.8 Nm (1.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T30 socket
  22. Release the barrel clip, move the LH front window motor/regulator assembly beams together, and then remove the regulator through the opening in the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    The barrel clip may not be equipped on all vehicles.

Install

  1. Position the LH front window motor/regulator assembly into the door, align the studs through the holes in the inner door, and then secure the barrel clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align all four studs through holes in inner door and secure barrel clip to stud
  2. Install the nuts (x2) that attach the rear section of the LH front window regulator to the door.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  3. Install the nuts (x2) that attach the front section of the LH front door window regulator to the door.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  4. Install the screws (x3) that attach the LH front window motor to the door.
    1.8 Nm (1.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T30 socket
  5. Connect the LH front window motor.
  6. Connect the LH front door cinch motor connector.
  7. Install the LH front door closeout panel, but do not install the door trim panel yet. See Closeout Panel - Door - Front - LH (Remove and Replace).
  8. Connect the LH door pressure sensor connector, and then secure the locking tab.
  9. Connect LV power. See LV Power (Disconnect and Connect).
  10. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  11. Position the LH front door glass into the door, and then install the front clip on the LH front window motor/regulator assembly.
  12. Fully lower the LH front window, and then disconnect the window switch.
    Informational PurposesAn informational icon, calling your attention
    Note
    Connect door panel x927 if the switch kit is not available.
  13. Install the LH front door outer belt seal . See Seal - Outer Belt - Front Door - LH (Remove and Replace).
  14. Raise the regulator for access to the rear window glass clamp.
  15. Position the window glass to the previous marks, and then tighten the nut that attaches the rear of the window glass to the regulator.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  16. Remove the alignment tape from the glass and trim.
  17. Check the gap between the LH front window and the B-pillar applique.
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to CVIS for current specifications.
  18. Install the butyl patch that covers the access hole for the rear window regulator nut.
  19. Position the LH front door controller module backing plate to the module, and then install the bolts (x4) that attach the plate to the module.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 8 mm socket
  20. Fully lower the LH front window, and then disconnect the window switch special tool.
  21. Install the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace).
  22. Install the LH front door trim decor. See Decor - Trim - Front Door - LH (Remove and Replace).
  23. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
  24. Press the LH front window switch down to the second position to activate the auto-lower function, then raise the window completely to activate the auto-raise function.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the window does not lower completely, repeat previous calibration steps.
  25. Raise the front windows and close the LH front door.