17/06/2022 13:36:37

Sensor - Resistive Occupancy - Front Seat - LH (Remove and Replace)

20202102 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Remove the LH front seat from the vehicle. See Seat Assembly - 1st Row - LH (Remove and Install).
  2. Place front seat on a protected surface
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Place seat so the underside of the seat can be accessed
  3. Remove screw securing outer side cover from LH front seat
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 4 Nm, Ensure the front of the seat is high enough to access the T20 screw
  4. Release LH outer side cover from seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clip, Carefully release outer side cover from seat, do not fully remove
  5. Disconnect LH front seat switch connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  6. Remove inboard side shield from LH front seat
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, Carefully release clips securing inboard side shield onto LH front seat
  7. Release seat back elastic straps from seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x straps
  8. Release soft trim retainers from seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x retainers
  9. Disconnect FSC vent heat pad from seat controller
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  10. Remove FSC and FSB vent heat pad harnesses from seat
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x bracket, Note one harness is for the seat cushion and the other is for the seat back. The upper bracket aids in routing while the lower clip secures them
  11. Remove LH front seat harness from seat frame bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x fir tree clip
  12. Remove OCS harness from SBR bracket then disconnect
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x bracket, Slide connector upward to release from bracket
  13. Slide SBR bracket upward to release from seat frame
  14. Open SBR bracket containing OCS harness and route harness between cushion and frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, Release tabs to open bracket, Routing harness will avoid getting snagged when seat foam is removed from frame
  15. Release soft trim retainer from inboard side of seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retainer
  16. Release soft trim retainer from outboard side of seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retainer
  17. Release soft trim retainer from front end of seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retainer
  18. Position seat upright
  19. Remove seat cushion from frame
  20. Release seat cushion trim from below seat foam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x strap
  21. Release Velcro securing 40 seat cushion trim cover to foam pad
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold back until you reach first row of hog rings
  22. Remove front hog rings securing seat cushion trim cover to foam pad
    Informational PurposesAn informational icon, calling your attention
    Note
    5x hog rings, Push down on foam to allow access to rings, Verify any excess pieces have been removed from foam
  23. Release remaining Velcro securing seat cushion trim cover to foam pad
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold back until access to OCS is clear
  24. Feed OCS harness through seat bottom foam access hole
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift up on cushion bottom to fully pull harness through foam
  25. Install OCS onto seat bottom cushion
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply pressure to area where double sided adhesive is applied to seat bottom foam, See image for clarity on locating indentations
  26. Feed OCS harness through access hole on seat cushion bottom foam
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift up on cushion bottom to fully pull harness through foam
  27. Secure Velcro to seat cushion bottom foam
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure up to the section where hog rings will be installed
  28. Install hog rings securing seat cushion trim to foam
    Informational PurposesAn informational icon, calling your attention
    Note
    5x hog rings, Push down on foam to allow access, Place hog ring into pliers prior to installation, Start with center ring and work your way out
  29. Install remaining portion of Velcro securing cushion trim cover to foam pad
    Informational PurposesAn informational icon, calling your attention
    Note
    Wrap remaining portion of trim cover over foam pad
  30. Flip cushion over and secure trim strap to foam
    Informational PurposesAn informational icon, calling your attention
    Note
    1x strap, Strap located on bottom side of cushion
  31. Install seat bottom cushion onto seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    Feed trim between seat back and seat frame, Maneuver seat assembly as needed for access
  32. Rotate seat assembly onto seat back
    Informational PurposesAn informational icon, calling your attention
    Note
    Protect seat from damage
  33. Install soft trim retainer onto front end of seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retainer
  34. Install soft trim retainer from outboard side of seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retainer
  35. Install soft trim retainer from inboard side of seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retainer
  36. Install OCS harness into SBR bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, Once harness is positioned, Verify tabs are fully engaged
  37. Slide SBR bracket downward to install onto seat frame bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  38. Connect OCS harness and install onto SBR bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x bracket
  39. Secure LH front seat harness onto seat frame bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x fir tree clip
  40. Route FSC and FSB vent heat pad harnesses onto plastic brackets
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip, 1x bracket, Note one harness is for the seat cushion and the other is for the seat back. The upper bracket aids in routing while the lower clip secures them
  41. Connect FSC vent heat pad from LV seat controller
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  42. Install soft trim retainers onto seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x retainers
  43. Install seat back elastic straps onto seat frame
    Informational PurposesAn informational icon, calling your attention
    Note
    2x straps
  44. Position seat upright
  45. Install inboard side shield onto LH front seat
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, fully secure inboard side shield onto LH front seat
  46. Connect LH outer side cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  47. Install LH outer side cover onto seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clip, Apply pressure to the outer seat cover to fully seat trim clips, trim should sit flush against the seat cushion
  48. Install screw securing outer side cover to LH front seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 4 Nm, Maneuver seat assembly as needed for access
  49. Install the LH front seat. See Seat Assembly - 1st Row - LH (Remove and Install).