29/08/2022 14:17:38

Trim - Liftgate Trough - Center (Remove and Replace)

Correction code 12272002 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH front doors.
  2. Lower the LH and RH front windows.
  3. Move the LH and RH front seats forward.
  4. Open the LH and RH falcon wing doors.
  5. Fold the 2nd row 40 and 60 seats downward.
  6. Open the liftgate.
  7. Remove the LH and RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  8. Remove the LH and RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  9. Remove the LH and RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  10. Remove the liftgate power strut. See Power Strut - Liftgate (Remove and Replace).
  11. Partially release the clips (x7) that attach the RH rear headliner to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  12. Disconnect the liftgate harness connectors (x4).
  13. Release the clips (x5) that attach the liftgate harness to the body.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  14. Remove the bolt that attaches the liftgate harness ground strap to the body.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  15. Release the liftgate harness grommet from the body, and then remove the harness from the vehicle.
  16. Remove the screws (x2) that attach the center liftgate trough trim to the body.
    Tip: Use of the following tool(s) is recommended:
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
    • Torx T20 socket
  17. Release the clips (x4) and double sided tape strips (x5) that attach the center liftgate trough trim to the body, and then remove the trim from the vehicle.

Install

  1. Use IPA wipes to clean and remove adhesive residue from the body surface area. Allow 1 minute dry time.
    Tip: Use of the following tool(s) is recommended:
    • IPA wipes
  2. Remove the backing tape from the center liftgate trough trim, position the trim on the vehicle, and then install the clips (x4) and double sided tape strips (x5) that attach the trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Partially lift the main seal for better access if needed.
  3. Install the screws (x2) that attach the center liftgate trough trim to the body.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
    • Torx T20 socket
  4. Position the liftgate harness on the vehicle, and then install the harness grommet on the body.
  5. Install the bolt that attaches the liftgate harness ground strap to the body.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  6. Install the clips (x5) that attach the liftgate harness to the body.
  7. Connect the liftgate harness connectors (x4).
  8. Install the clips (x7) that attach the RH rear headliner to the vehicle.
  9. Install the LH and RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  10. Install the LH and RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  11. Install the LH and RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  12. Install the liftgate power strut. See Power Strut - Liftgate (Remove and Replace).
  13. Close the liftgate.
  14. Fold the 2nd row 40 and 60 seats into original position.
  15. Close the LH and RH falcon wing doors.
  16. Move the LH and RH front seats to original position.
  17. Close the LH and RH front doors.
  18. Raise the LH and RH front windows.
  19. Close the LH and RH front doors.