10/12/2024 13:43:59

Fixed Glass - Rear Door - LH (Remove and Replace)

Correction code 11501602 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-12-10: Added new caution about Pre-Installation Glass Inspection service requirements.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in Pre-Installation Glass Inspection before beginning this procedure.

Remove

  1. Open the LH front door.
  2. Lower the LH front window.
  3. Lower the LH rear window.
  4. Open the LH falcon wing door.
  5. Remove the LH rear door trim lower garnish. See Garnish - Lower - Door Trim - Rear - LH (Remove and Replace).
  6. Remove the LH rear door trim decor. See Decor - Trim - Rear Door - LH (Remove and Replace).
  7. Remove the LH rear trim door panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  8. Remove the LH rear door inner belt seal. See Seal - Inner Belt - Rear Door - LH (Remove and Replace).
  9. Remove the bolt and fir clip that attaches the LH falcon wing door airbag to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • Clip pry tool
  10. Fold the LH falcon wing door airbag downwards.
  11. Partially release the push clips (x7) that attach the rear pinch sensor to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  12. Remove the bolts (x5) that attach the LH rear door fixed glass to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 4 in extension
    • Flex head ratchet/flex head torque wrench
    • Torx T25 socket
  13. Remove the LH rear door outer belt seal. See Seal - Outer Belt - Rear Door - LH (Remove and Replace).
  14. Partially release the LH rear window seal.
  15. Remove the LH rear door fixed glass from the vehicle.

Install

  1. Position the LH rear door fixed glass on the vehicle.
  2. Install the LH rear window seal.
  3. Install the LH rear door outer belt seal. See Seal - Outer Belt - Rear Door - LH (Remove and Replace).
  4. Install the bolts (x5) that attach the LH rear door fixed glass to the vehicle.
    4.5 Nm (3.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Ratchet/torque wrench
    • Torx T25 socket
  5. Install the push clips (x7) that attach the rear pinch sensor to the vehicle.
  6. Move the LH falcon wing door airbag into original position.
  7. Install the bolt and fir clip that attaches the LH falcon wing door airbag to the vehicle.
    7 Nm (5.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  8. Install the LH rear door inner belt seal. See Seal - Inner Belt - Rear Door - LH (Remove and Replace).
  9. Install the LH rear trim door panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  10. Install the LH rear door trim decor. See Decor - Trim - Rear Door - LH (Remove and Replace).
  11. Install the LH rear door trim lower garnish. See Garnish - Lower - Door Trim - Rear - LH (Remove and Replace).
  12. Close the LH falcon wing door.
  13. Raise the LH rear window.
  14. Raise the LH front window.
  15. Close the LH front door.