06/03/2024 02:06:49

Raise Vehicle - Floor Jack (Mobile Service)

Correction code 10001105 0.10 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-03-07: Added a warning to stay away from the vehicle before lifting to avoid injury.
  • 2023-08-16: Added to set air suspension to "Very High" before Jack Mode is enabled.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure details vehicle lifting for Mobile Service using a floor jack and supporting the vehicle on a jack stand. ONLY USE THIS PROCEDURE WHEN IT IS REFERENCED BY ANOTHER PROCEDURE.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
To reduce the risk of personal injury, use appropriate equipment while performing this operation.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Do not work on an incorrectly supported vehicle.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Failure to follow the critical steps and checks of this procedure can lead to serious injury or death.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
To avoid damage, NEVER support the vehicle from diagonal points (for example, LH front and RH rear) at the same time.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Perform a visual check of the floor jack according to the equipment operator's manual before using the floor jack.

Raise

  1. Ensure the vehicle is parked on a level surface.
  2. On the vehicle touchscreen, touch Controls > Suspension > Very High to set the air suspension to the "Very High" setting.
  3. On the vehicle touchscreen, touch Controls > Service > Jack Mode to activate Jack Mode.
  4. Make sure that the hood, trunk, and all doors are closed, unless necessary for the work to be performed.
  5. Install wheel chocks on the wheel that is diagonally across from where the vehicle will be lifted, for example:
    • Lift LH front of vehicle: chock RH rear wheel
    • Lift RH front of vehicle: chock LH rear wheel
    • Lift LH rear of vehicle: chock RH front wheel
    • Lift RH rear of vehicle: chock LH front wheel
  6. Position the jack stand adapter on the floor jack.
  7. Position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
    Figure 1. LH rear lift point shown; other corners similar
  8. Lift the vehicle until there is enough clearance for a jack stand under the vehicle, and then place a jack stand under the jack stand adapter.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If an electric jack or pneumatic jack is used, stay away from the vehicle prior to raising it to avoid injuries.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the jack stand cutout with the floor jack.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the top opening of the jack stand with the bottom of the jack stand adapter.
  9. Slowly lower the floor jack, making sure the jack stand is aligned with the jack stand adapter.
  10. Move the floor jack out of the working area.
  11. If installing another jack stand on the same axle or same side of the vehicle, repeat steps 5 to 10.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To avoid damage, NEVER support the vehicle from diagonal points (for example, LH front and RH rear) at the same time.

Lower

  1. Make sure no tools or parts are under the vehicle.
  2. Position the floor jack under the jack stand, and then carefully lift the vehicle off of the jack stand(s).
  3. Remove the jack stand(s) from under the vehicle.
  4. Slowly lower the vehicle until the wheels are touching the ground.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To avoid injuries, stay clear from the vehicle.
  5. Remove the floor jack from under the vehicle.
  6. Remove the wheel chocks from the vehicle.
  7. On the vehicle touchscreen, touch Controls > Service > Jack Mode to deactivate Jack Mode.
  8. On the vehicle touchscreen, touch Controls > Suspension and set the air suspension to the previous setting. If not sure, set the air suspension to "Medium".