01/04/2024 14:00:43

Actuator - Bypass - 2nd Row - HVAC Case (Remove and Replace)

Correction code 18109602 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Open RH front door
  2. Lower RH front window
  3. Move RH front seat backward
  4. Remove RH front floor mat
  5. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 1x connector, 4x datums
  6. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  7. Remove screws securing 2R Bypass HVAC Actuator and remove from HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2.3 Nm, 1x datum
  8. Disconnect 2R Bypass HVAC Actuator connector and remove actuator from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 2x datums, Release harness from HVAC assembly
  9. Connect 2R Bypass HVAC Actuator connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 2x datums, Secure harness to HVAC assembly
  10. Install screws securing 2R Bypass HVAC Actuator to HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2.3 Nm, 1x datum, Actuator is keyed to HVAC assembly, Ensure alignment before installing screws
  11. Install RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  12. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 4x datums, 1x connector
  13. Install RH front floor mat
  14. Release IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, 4x datums, Release top tabs and slide rearward
  15. Using laptop connect to vehicle with ethernet diag kit and Toolbox 3
  16. Select "Actions" and search for "Actuator"
  17. Select TEST-SELF_VCRIGHT_X_HVAC-CASE-ACTUATORSvia Toolbox: (link), click "Run", and allow routine to complete
    Informational PurposesAn informational icon, calling your attention
    Note
    Select "X" at top right of window to close once complete
  18. Disconnect Toolbox 3 from vehicle and remove laptop and ethernet diag kit
  19. Install IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs, 4 datums, Slide forward engaging datums then secure tabs upward into IP
  20. Move RH front seat to original position
  21. Raise RH front window
  22. Close RH front door