17/06/2022 13:02:26

T Badge Support - Fascia - Front (Remove and Replace)

Correction code 10011512 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open LH front door and lower the front windows.
  2. Remove the front fascia assembly from the vehicle. See Fascia Assembly - Front (Remove and Install).
  3. Disconnect the front BLE module electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  4. Remove the screw and release the tabs (x6) that attach the front fascia T-badge support to the front fascia assembly, and then remove the T-badge support from the front fascia.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  5. Remove the screws (x2) that attach the front fascia V-bar to the front fascia T-badge support.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  6. Release the clips (x4) that attach the front fascia V-bar to the front fascia T-badge support, and then remove the V-bar from the T-badge support.
  7. Remove the screws (x2) that attach the front BLE module to the front fascia T-badge support, and then remove the module from the assembly.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  8. Remove the screws (x2) that attach the front T-badge to the front fascia T-badge support, and then remove the T-badge from the T-badge support.
    1.8 Nm (1.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket

Install

  1. Position the front T-badge onto the front fascia T-badge support, and then install the screws (x2) that attach the T-badge to the T-badge support.
    1.8 Nm (1.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  2. Position the front BLE module onto the front fascia T-badge support, and then install the screws (x2) that attach the module to the assembly.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  3. Position the front fascia V-bar onto the front fascia T-badge support, and then secure the clips (x4) that attach the V-bar to the T-badge support.
  4. Install the screws (x2) that attach the front fascia V-bar to the front fascia T-badge support.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  5. Position the front fascia T-badge support assembly onto the front fascia assembly, and then install the screw and secure the tabs (x6) that attach the T-badge support to the front fascia.
    3 Nm (2.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  6. Connect the front BLE module electrical connector, and then engage the locking tab.
  7. Install the front fascia assembly. See Fascia Assembly - Front (Remove and Install).
  8. Raise the front windows and close the LH front door.