17/06/2022 13:25:23
Harness - Center Console (Remove and Replace)
Correction code
17100302
1.62
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate Times to learn
more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com.
NOTE: See Personal Protection to make sure proper PPE is worn when
performing the below
procedure.
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
- Open all four doors
- Move LH front seat forward
- Move RH front seat forward
-
Release console back panel assembly
Note6x clips, 7x datums, Disengage bottom clips last and pull rearward due to alignment
-
Remove console back panel assembly
Note1x connector, Connector lock for lamp located underneath bracket
-
Release LH and RH rear console carrier
Note2x bolts, 10mm, 12 Nm
-
Remove center console rear cupholder assembly screws
Note6x screws, T20, 1 Nm
-
Release center console rear cupholder assembly
Note3x clips, 2x datums, Pull straight down at rear of assembly and rotate datums out of center console lower frame
-
Remove center console rear cupholder assembly
Note1x connector
- Move RH front seat backward
- Move LH front seat backward
-
Access front center console storage compartment
NoteFully retract center console lid, cupholder, and sliding tray into locked position
-
Release center console service panel
Note4x clips, Release clips and pull panel up to access harness, Use 90 degree plastic trim tool
-
Release center console service panel connectors and remove assembly
Note3x connectors, 1x clip
-
Release phone dock
Note4x clips, 2x datums, Pull up at bottom and swing out from under instrument panel
-
Remove phone dock
Note3x connectors, 1x clip, Take caution to release connector locks before pulling straight out of each socket to avoid damage
-
Release IP service panel
Note2x tabs, 4x datums, Release top tabs and slide rearward
-
Release diagnostic and CAN harnesses from IP service panel
Note2x clips
-
Remove IP service panel
Note1x connector
-
Remove LH outboard footwell cover
Note2x magnets, 2x datums
-
Remove LH inboard footwell cover
Note1x cover, 1x clip, 1x datum, 1x screw, 8 mm, 1 Nm
-
Remove LH console side carpet
Note11x clips, 2x datums
-
Release LH center console lower bracket from IP carrier
Note1x bolt, 10mm, 10 Nm
-
Remove RH footwell cover
Note3x magnets, 1x connector, 4x datums
-
Remove RH console side carpet
Note11x clips, 2x datums
-
Release RH center console lower bracket from IP carrier
Note1x bolt, 10mm, 10 Nm
-
Release center console connectors to body harness
Note4x connectors
-
Release console carrier center bracket
Note2x bolts, 10mm, 12 Nm
- Recline LH front seat backrest
- Recline RH front seat backrest
-
Remove console assembly
NoteLift at rear, rotate front from under IP and out passenger door, Take care not to scratch seats, IP or inner door panel, Recommend assistance if needed
-
Remove LH and RH console side panels
Note17x clips each side
-
Release decor harness from console assembly
Note6x connectors, 2x clips, 2x connectors wrapped in felt tape, Wrap connecters in felt tape after re-assembly
-
Release decor from console assembly
Note18x screws, T20, 1 Nm
-
Remove rear bright strip screws
Note2x screws, T20, 1 Nm, Removal of screws allows flexibility to disengage decor bright
-
Remove console decor assembly
Note6x datums, 1x connector, Lift up at front and slide out of rear bright strip
-
Release console airwave cap
Note6x screws, T20, 1 Nm, 1x connector, 3x tabs, Pull airwave cap straight back then to the right to access connector
-
Remove airwave cap
Note1x screw, T20, 1 Nm, Release ground harness with screw
-
Release console harness from airwave assembly and actuators
Note5x connectors, 1x clip
-
Release console airwave assembly
Note5x screws, T20, 1 Nm, Pull airwave assembly straight rearward and rotate to the left to access air duct temp sensor harness
-
Remove console airwave assembly
Note1x connector, 1x clip, 2x datums, Pull airwave assembly rearward at the top then out of the datums in the lower center console frame
-
Remove console armrest assembly
Note6x bolts, T20, 1 Nm, Remove bolts and slide armrest assembly rearward
-
Remove the fasteners for center console storage bin assembly
Note16x bolts, T20, 1Nm
-
Remove the center console storage bin assembly from the center console base
Note1x connector, Press in on side and carefully lift up, unplug console light during removal
-
Remove harness from center console frame
Note14x clips
-
Install center console harness to center console
Note14x clips
-
Install center console storage bin to assembly
Note1x connector
-
Install fasteners to center console storage bin
Note16x bolts, T20, 1 Nm, ensure shorter chrome headed bolts are on the rear storage bin to prevent damage to center console
-
Install console armrest assembly
Note6x bolts, T20, 1 Nm, Slide armrest down and align arms with console assembly
-
Install console airwave assembly
Note1x connector, 1x clip, 2x datums, Connect airwave duct temp sensor and secure harness before install, Engage both datums at bottom of center console frame
-
Secure console airwave assembly
Note5x screws, T20, 1 Nm
-
Secure console harness to airwave assembly and actuators
Note5x connectors, 1x clip
-
Secure airwave cap
Note1x screw, T20, 1 Nm
-
Install console airwave cap
Note4x screws, T20, 1 Nm, 1x connector, 3x tabs, Secure display connector, align airwave cap with console assembly and insert straight forward
-
Position center console service panel, Secure center console service panel connectors
Note3x connectors, 1x clip
-
Secure center console service panel
Note4x clips, 3x datums, Ensure connector X1131 and X881 is positioned to the right of the main harness for USB hub clearance, Engage datums at bottom of service panel then secure clips
-
Install console decor assembly
Note6x datums, 1x connector, Slide into rear bright strip and down into console assembly, Ensure all 6 datums engage and bright strip is aligned
-
Install rear bright strip screws
Note2x screws, T20, 1 Nm, Confirm alignment of decor bright with rear bright trim
-
Secure decor to console assembly
Note18x screws, T20, 1 Nm
-
Secure decor harness to console assembly
Note6x connectors, 2x clips, 2x connectors wrapped in felt tape, Wrap connecters in felt tape after re-assembly
-
Install LH and RH console side panels
Note17x clips each side
-
Install console assemby
NoteCarefully maneuver front of assembly under and into IP carrier and lower rear into place, Recommend assistance if needed
-
Secure LH center console lower bracket to IP carrier
Note1x bolt, 10mm, 10 Nm
-
Secure RH center console lower bracket to IP carrier
Note1x bolt, 10mm, 10 Nm
-
Secure center console connectors to body harness
Note4x connectors, Ensure all connector locks engage
-
Secure console carrier center bracket
Note2x bolts, 10mm, 12 Nm
-
Install RH console side carpet
Note11x clips, 2x datums
-
Install RH footwell cover
Note3x magnets, 4x datums, 1x connector
-
Install LH console side carpet
Note11x clips, 2x datums
-
Install LH inboard footwell cover
Note1x cover, 1x clip, 1x datum, 1x screw, 8 mm, 1 Nm, Align datums and footwell vent before installing screw
-
Install LH outboard footwell cover
Note2x magnets, 2x datums
-
Secure diagnostic and CAN harnesses to IP service panel
Note2x clips
-
Install IP service panel
Note2x tabs, 4 datums, Slide forward engaging datums then secure tabs upward into IP
-
Install phone dock connections
Note3x connectors, 1x clip
-
Install phone dock
Note2x datums, 4 tabs, Slide datums forward into IP and secure tabs down into center console
- Move LH front seat forward
- Raise LH front seat backrest
- Move RH front seat forward
- Raise RH front seat backrest
-
Install center console rear cupholder assembly
Note1x connector
-
Secure center console rear cupholder assembly
Note3x clips, 2x datums, Position datums and rotate assembly up into rear center console frame
-
Install center console rear cupholder assembly screws
Note6x screws, T20, 1 Nm
-
Secure LH and RH rear console carrier
Note2x bolts, 10mm, 12 Nm
-
Install console back panel assembly
Note1x connector
-
Secure console back panel assembly
Note6x clips, 7x datums, Engage bottom clips first due to forward facing alignment
- Move RH front seat to original position
- Move LH front seat to original position
- Close all four doors