01/04/2024 14:03:53

Sensor - Parking Distance - Outer - Rear (HW3) (Remove and Replace)

Correction code 17271122 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Informational PurposesAn informational icon, calling your attention
Note
This procedure is applicable to sensors S7 and S12.

Remove

  1. On the vehicle touchscreen, touch Controls > Suspension > Very High.
  2. On the vehicle touchscreen, touch Controls > Service > Jack Mode to activate Jack Mode.
  3. Disconnect LV Power. See LV Power (Disconnect and Connect).
  4. Remove the clips (x2) that attach the rear portion of the rear fender garnish to the wheel arch liner.
    Figure 1. LH shown; RH similar
  5. Remove the bolts (x2) that attach the rear portion of the rear fender garnish to the wheel arch liner.
    Figure 2. LH shown; RH similar
  6. Release the clips (x3) and tabs (x7) that attach the rear portion of the fender garnish to the vehicle, and then carefully set the garnish aside.
    Figure 3. LH shown; RH similar
    Figure 4. LH shown; RH similar
  7. Remove the screw that attaches the rear fascia to the quarter panel.
  8. Partially release the LH side of the rear fascia from the rear wing bracket.
    Figure 5. LH shown; RH similar
  9. Release the connector lock, and then disconnect the rear outer parking distance sensor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    Figure 6. LH shown; RH similar
  10. Release the tabs that attach the rear outer parking distance sensor to the rear fascia assembly, and then remove the sensor from the assembly.
    Figure 7. LH shown; RH similar

Install

  1. Install the rear outer parking distance sensor on the rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the sensor is seated flush to rear fascia.
  2. Connect the rear outer parking distance sensor, and then engage the locking tab.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  3. Install the LH side of the rear fascia on the rear wing bracket.
    Figure 8. LH shown; RH similar
  4. Install the screw that attaches the rear fascia to the quarter panel.
    1.5 Nm (1.1 lbs-ft)
  5. Position the rear portion of the fender garnish on the vehicle, and then install the clips (x3) and tabs (x7) that attach the fender garnish to the vehicle.
    Figure 9. LH shown; RH similar
    Figure 10. LH shown; RH similar
  6. Install the bolts (x2) that attach the rear portion of the rear fender garnish to the wheel arch liner.
    5 Nm (3.7 lbs-ft)
    Figure 11. LH shown; RH similar
  7. Install the clips (x2) that attach the rear portion of the rear fender garnish to the wheel arch liner.
    Figure 12. LH shown; RH similar
  8. Connect LV power. See LV Power (Disconnect and Connect).
    Informational PurposesAn informational icon, calling your attention
    Note
    After connecting LV power, do not shift the vehicle to Drive until the Toolbox routine (further below) is performed. Failure to do so can trigger vehicle alerts.
  9. Hold the LH and RH upper B-pillar buttons in the "Close" position to manually calibrate the LH and RH rear doors.
  10. On the vehicle touchscreen, touch Controls > Service > Jack Mode to deactivate Jack Mode.
  11. On the vehicle touchscreen, touch Controls > Suspension > Standard.
  12. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  13. In Toolbox, click the Actions tab, type TEST-RESET_PARKvia Toolbox: (link) into the search field, click TEST-RESET_PARKvia Toolbox: (link), click Run, and then allow the routine to complete.
  14. In Toolbox, click the Actions tab, type "USS Addresses" into the search field, click PROC_USM_REAR_PROGRAM-USS-ADDRESSESvia Toolbox: (link)via Service Mode: Driver Assist ➜ Sensors ➜ Program Rear USS, click Run, and then allow the routine to complete.
  15. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
  16. Raise the front windows and close the LH front door.