10/11/2022 08:08:38

Seat Assembly - 2nd Row - LH (7 Seat) (Remove and Replace)

Correction code 13050052 1.08 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open all the doors and lower the front windows.
  2. Release the clips (x2) that attach the instrument service panel to the instrument panel, and then remove the service panel from the IP.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the top tabs, and then slide the service panel rearward.
  3. Open the hood.
  4. Move the driver seat forward.
  5. Move the LH 2nd row seat fully forward.
  6. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  7. Apply masking tape to the LH racetrack.
  8. Repeat step 4 through step 7 for the RH side of the vehicle.
  9. Open the liftgate.
  10. Remove the RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  11. Remove the RH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  12. Repeat steps 10 and 11 for the LH side of the vehicle.
  13. Move the 2nd row seats out of easy entry position.
  14. Remove the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (7 Seat) (Remove and Replace).
  15. Remove the 2nd row rear floor panel. See Floor Panel - Rear - 2nd Row (7 Seat) (Remove and Replace).
  16. Remove and discard the bolts (x6) that attach the LH 2nd row seat rear bracket to the vehicle.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  17. Move the LH 2nd row seat fully rearward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Latch the seat back to lock it into position.
  18. Remove the LH 2nd row rear floor supports.
  19. Remove the LH 2nd row seat outboard front floor plate. See Front Floor Plate - Outboard - 2nd Row Seat - LH (7 Seat) (Remove and Replace).
  20. Remove the LH 2nd row seat inboard front floor plate. See Front Floor Plate - Inboard - 2nd Row Seat - LH (7 Seat) (Remove and Replace).
  21. Remove the bolts (x6) that attach the LH 2nd row seat front bracket to the vehicle.
    45 Nm (33.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  22. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  23. Disconnect LV power. See LV Power (Disconnect and Connect).
  24. Disconnect the LH 2nd row seat harness electrical connectors (x3).
    Tip: Release the bracket for access to the connectors if needed.
  25. Release the clips (x2) that attach the harness from the LH floor support bracket.
  26. Fold the LH 2nd row seat to the down position.
  27. With assistance, remove the LH 2nd row seat assembly from the vehicle.

Install

  1. With assistance, position the LH 2nd row seat into the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the guide pins are properly aligned.
  2. Move the LH 2nd row seat back to the upright position.
  3. Install and hand tighten new bolts (x6) that attach the LH 2nd row seat front bracket to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolts will be torqued at a later step.
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  4. Secure the clips (x2) that attach the LH 2nd row seat harness to the LH 2nd row floor support bracket.
  5. Connect the LH 2nd row seat harness electrical connectors (x3), and then secure the connector housing to the bracket.
    Tip: Release the bracket for access to the connectors if needed.
  6. Connect LV power. See LV Power (Disconnect and Connect).
  7. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  8. Close the hood.
  9. Move LH 2nd row seat fully forward.
  10. Install new bolts (x6) that attach the LH 2nd row seat rear bracket to the vehicle.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Torque the center bolt on each side before the outer bolts.
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  11. Install the LH 2nd row rear floor supports.
  12. Position the 2nd row rear floor panel into the vehicle, and then secure the clips (x2) that attach the panel to the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution near the center console display.
  13. Move the LH 2nd row seat rearward and out of easy entry position.
  14. Torque the bolts (x6) that attach the LH 2nd row seat front bracket to the vehicle.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Torque the most forward bolt on each side before the outer bolts.
    Tip: Use of the following tool(s) is recommended:
    • 11 mm socket
  15. Position the LH 2nd row seat inboard front floor plate into the vehicle, secure the clip that attaches the floor plate to the vehicle, and then install the front plate decal onto the seat track base to cover the fastener.
  16. Position the LH 2nd row seat outboard front floor plate into the vehicle, secure the clip that attaches the floor plate to the vehicle, and then install the front plate decal onto the seat track base to cover the fastener.
  17. Move the RH 2nd row seat rearward and out of easy entry position.
  18. Position the 2nd row mid floor panel into the vehicle, and then secure the clips (x5) that attach the panel to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace all damaged clips.
  19. Move the LH and RH 2nd row seats fully forward.
  20. Install the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  21. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  22. Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  23. Repeat step 20 through step 22 for the RH side of the vehicle.
  24. Position the LH trunk sill side trim into the vehicle, and then secure the clips (x4) that attach the trim to the vehicle. Repeat this step for the RH trunk sill side trim.
  25. Close the liftgate.
  26. Move the RH 2nd row seat to the original position.
  27. Close the RH front door.
  28. Move the LH 2nd row seat to the original position.
  29. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
  30. Move the driver seat to the original position.
  31. Connect a laptop with Toolbox 3 to the vehicle.
  32. Click the Actions tab, and then search for "Service-Redeploy".
  33. Click SERVICE CAN REDEPLOY, and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    The routine will state pass but the update will continue to run in the background.
    Informational PurposesAn informational icon, calling your attention
    Note
    The UI will show the update progress.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click the X at the top right of window to close once complete.
  34. Position the instrument panel service panel into the instrument panel, and then secure the tabs (x2) that attach the panel to the IP.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the panel forward to engage the datums, and then secure the tabs upward into the IP.
  35. Raise the front windows and close the LH front door.