12/10/2022 13:59:58

Harness - Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace)

Correction code 17100122 1.86 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the RH 2nd row seat seat back sub-assembly. See Seat Back Sub-assembly - 2nd Row Seat - RH (7 Seat) (Remove and Replace).
  2. Remove the screws (x3) that attach the inboard seat riser cover to the LH 2nd row inboard seat riser.
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  3. Remove the screw that attaches the outboard seat riser cover to the LH 2nd row inboard seat riser.
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  4. Release the clips (x2) that attach the outboard seat riser cover to the LH 2nd row inboard seat riser, and then remove the inboard and outboard covers from the seat riser.
  5. Disconnect the RH 60/40 seat switch electrical connector.
  6. Disconnect the release track actuator electrical connector.
  7. Release the locking tab, and then disconnect the seat belt harness electrical connector.
  8. Release the clips (x6) that attach the RH 2nd row seat harness to the seat frame, and then disconnect the controller ECU electrical connectors (x2).
  9. Release the clips (x3) that attach the RH 2nd row seat harness to the backrest frame.
  10. Release the clips (x3) that attach the RH 2nd row seat harness to the cushion frame.
  11. Release the clips (x2) that secure the RH 2nd row seat harness to the securing guide bracket.
  12. Disconnect the RH 2nd row seat seat track position sensor electrical connector.
  13. Disconnect the RH 2nd row seat occupancy sensor electrical connector.
  14. Disconnect the RH 2nd row seat buckle sensor electrical connector.
  15. Carefully maneuver the RH 2nd row seat harness through the outboard seat riser into the center section.
  16. Disconnect the RH 2nd row seat recliner easy entry microswitch electrical connector.
  17. Disconnect the recline release actuator electrical connector.
  18. Remove the RH 2nd row seat assembly harness from the seat assembly.

Install

  1. Position the RH 2nd row seat assembly harness into the seat assembly.
  2. Connect the recline release actuator electrical connector.
  3. Connect the RH 2nd row seat recliner easy entry microswitch electrical connector.
  4. Carefully maneuver the RH 2nd row seat harness through the outboard seat riser.
  5. Connect the RH 2nd row seat buckle sensor electrical connector.
  6. Connect the RH 2nd row seat occupancy sensor electrical connector.
  7. Connect the RH 2nd row seat seat track position sensor electrical connector.
  8. Position the RH 2nd row seat harness into the securing guide bracket, and then secure the clips (x2) that attaches the harness to the bracket..
  9. Position the inboard and outboard seat riser covers onto the LH 2nd row inboard seat riser, and then secure the clips (x2) that attach the inboard and outboard covers to the seat riser.
  10. Install the screws (x3) that attach the inboard seat riser cover to the LH 2nd row inboard seat riser.
    2 Nm (1.5 lbs-ft)
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The top screw has a torque value of 4 Nm and the bottom screws (x2) have a torque value of 2 Nm.
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  11. Install the screw that attaches the outboard seat riser cover to the LH 2nd row inboard seat riser.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  12. Secure the clips (x3) that attach the RH 2nd row seat harness to the cushion frame.
  13. Secure the clips (x3) that attach the RH 2nd row seat harness to the backrest frame.
  14. Secure the clips (x6) that attach the RH 2nd row seat harness to the seat frame, and then connect the controller ECU electrical connectors (x2).
  15. Connect the seat belt harness electrical connector, and then secure the locking tab.
  16. Connect the release track actuator electrical connector.
  17. Connect the RH 60/40 seat switch electrical connector.
  18. Install the RH 2nd row seat seat back sub-assembly. See Seat Back Sub-assembly - 2nd Row Seat - RH (7 Seat) (Remove and Replace).