28/06/2022 14:03:01

Bracket - Tie Down - Rear Trunk - LH (Remove and Replace)

Correction code 15240032 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH front doors.
  2. Lower the LH and RH front windows.
  3. Move the driver and front passenger seats forward.
  4. Open the LH and RH falcon wing doors.
  5. Fold down the LH and RH 2nd row bench seats.
  6. Open the liftgate.
  7. Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  8. Remove the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
  9. Remove the trunk gap hider. See Gap Hider - Trunk (5 Seat) (Remove and Replace).
  10. Release the clip and tabs (x3) that attach the LH trunk side mini nub to the LH trunk load floor bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Plastic trim tool
  11. Release the clips (x4) that attach the LH trunk sill side trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Plastic trim tool
  12. Release the clips (x4) that attach the RH trunk sill side trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Plastic trim tool
  13. Remove the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  14. Remove the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  15. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  16. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  17. Remove the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  18. Release the clips (x2) and push clips (x4) that attach the rear wall load support to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Clip pry tool
    • Plastic trim tool
  19. Fold the trunk carpet upward.
  20. Remove the LH rear trunk crush can bracket. See Trim - Crush Can - Rear Trunk - LH (Remove and Replace).
  21. Release the push clip that attaches the LH soft trim pocket bracket to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Clip pry tool
  22. Release the fir tree clip that attaches the charge port manual cable release to the LH mid C-pillar zone bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Clip pry tool
  23. Remove the LH mid C-pillar zone bracket. See Bracket - Zone - C-Pillar - Mid - LH (5 Seat) (Remove and Replace).
  24. Release the LH rear trunk tie down ring that attaches the side trim carpet to the tie down.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Plastic trim tool
    • Pocket screwdriver
  25. Remove the LH trunk side trim carpet. See Carpet - Trim - Trunk - LH (Remove and Replace).
  26. Remove the LH rear trunk tie down. See Tie Down - Rear Trunk - LH (Remove and Replace).
  27. Remove the bolts (x2) that secure the LH rear trunk tie down bracket to the vehicle, and then remove the bracket from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench

Install

  1. Position the LH rear trunk tie down bracket on the vehicle, and then install the bolts (x2) that secure the bracket to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  2. Install the LH rear trunk tie down. See Tie Down - Rear Trunk - LH (Remove and Replace).
  3. Install the LH trunk side trim carpet. See Carpet - Trim - Trunk - LH (Remove and Replace).
  4. Install the LH rear trunk tie down ring that attaches the side trim carpet to the tie down.
  5. Install the LH mid C-pillar zone bracket. See Bracket - Zone - C-Pillar - Mid - LH (5 Seat) (Remove and Replace).
  6. Install the fir tree clip that attaches the charge port manual cable release to the LH mid C-pillar zone bracket.
  7. Install the push clip that attaches the LH soft trim pocket bracket to the vehicle.
  8. Install the LH rear trunk crush can bracket. See Trim - Crush Can - Rear Trunk - LH (Remove and Replace).
  9. Fold the trunk carpet downward.
  10. Install the clips (x2) and push clips (x4) that attach the rear wall load support to the vehicle.
  11. Install the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  12. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  13. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  14. Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  15. Install the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  16. Install the clips (x4) that attach the RH trunk sill side trim to the vehicle.
  17. Install the clips (x4) that attach the LH trunk sill side trim to the vehicle.
  18. Install the clip and tabs (x3) that attach the LH trunk side mini nub to the vehicle.
  19. Install the trunk gap hider. See Gap Hider - Trunk (5 Seat) (Remove and Replace).
  20. Install the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
  21. Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
  22. Close the liftgate.
  23. Fold the LH and RH 2nd row bench seats upward.
  24. Close the LH and RH falcon wing doors.
  25. Move the driver and front passenger seats to original position.
  26. Raise the LH and RH front windows.
  27. Close the LH and RH front doors.