Seat Assembly - 2nd Row - LH (5 Seat) (Remove and Replace)
Correction code 13050152 1.08 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Remove
- Open the LH front door and lower the front windows.
- Move the driver seat forward.
- Fold the LH 2nd row seat to the down position.
- Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
-
Apply masking tape to the LH racetrack
to avoid damage.
- Repeat step 2 through step 5 for the RH side of the vehicle.
- Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
- Remove the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
- Remove the trunk gap hider. See Gap Hider - Trunk (5 Seat) (Remove and Replace).
- Remove the RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
- Remove the RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
- Remove the RH trunk load floor bracket cover. See Cover - Bracket - Trunk Load Floor - LH (Remove and Replace).
- Remove the RH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
- Repeat step 10 through step 13 for the LH side of the vehicle.
- Remove the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (5 Seat) (Remove and Replace).
-
Fold the trunk carpet rearward.
NoteStarting from the front, lift the carpet over the harpoon brackets, and then fold the carpet back enough to access the rear seat components.
- Remove the 2nd row rear floor panel. See Floor Panel - Rear - 2nd Row (5 Seat) (Remove and Replace).
- Remove the LH 2nd row floor supports. See Floor Supports - Rear - 2nd Row - LH (Remove and Replace)
-
Remove and discard the bolts (x4) that
attach the LH 2nd row seat assembly rear brackets to the vehicle.Tip: Use of the following tool(s) is recommended:
- 11 mm socket
-
Remove and discard the bolts (x6) that
attach the LH 2nd row seat assembly front brackets to the vehicle.Tip: Use of the following tool(s) is recommended:
- 11 mm socket
- Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Disconnect LV power. See LV Power (Disconnect and Connect).
-
Disconnect the LH 2nd row seat harness
electrical connectors (x3).
NoteRelease the bracket for better access if needed.
-
Release the clips (x2) that attach the
LH 2nd row seat harness to the floor support bracket.
- With assistance, remove the LH 2nd row seat assembly from the vehicle.
Install
-
With assistance, position the LH 2nd
row seat into the vehicle.
NoteMake sure the guide pins are properly aligned.
-
Loosely install new bolts (x6) that attach the LH 2nd row seat assembly front
brackets to the vehicle.
Tip: Use of the following tool(s) is recommended:
- 11 mm socket
-
Install new bolts (x4) that attach the LH 2nd row seat assembly rear brackets to the
vehicle.Tip: Use of the following tool(s) is recommended:
- 11 mm socket
-
Tighten the bolts (x6) that attach the LH 2nd row seat assembly front brackets to the
vehicle.NoteTorque the most forward bolt on each side before the outer bolts.Tip: Use of the following tool(s) is recommended:
- 11 mm socket
-
Secure the clips (x2) that attach the LH 2nd row seat harness to the floor support
bracket.
-
Connect the LH 2nd row seat harness electrical connectors (x3).
NoteSecure the connector housing to the bracket.
- Install the LH 2nd row floor supports. See Floor Supports - Rear - 2nd Row - LH (Remove and Replace)
- Install the 2nd row rear floor panel. See Floor Panel - Rear - 2nd Row (5 Seat) (Remove and Replace).
-
Fold the trunk carpet to the original
position.
NoteFold carpet down over the harpoon brackets.
- Install the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (5 Seat) (Remove and Replace).
- Install the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
- Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
- Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
- Repeat step 11 through step 13 for the RH side of the vehicle.
- Install the LH and RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
- Install the trunk gap hider. See Gap Hider - Trunk (5 Seat) (Remove and Replace).
- Install the RH trunk load floor bracket cover. See Cover - Bracket - Trunk Load Floor - LH (Remove and Replace).
- Install the front trunk load floor. See Trunk Load Floor - Front (Remove and Replace).
- Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
- Connect LV power. See LV Power (Disconnect and Connect).
- Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Remove the masking tape from the RH lower C-pillar and from the race tracks.
- Fold the RH 2nd row seat to the upright position.
- Move the front passenger seat to the original position.
- Close the RH front door.
- Remove the masking tape from the LH lower C-pillar and from the race tracks.
- Fold the LH 2nd row seat to the upright position.
-
Calibrate the rear doors.
NoteIf the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
- Move the driver seat to the original position.