09/09/2022 14:57:33

Air Vent - Instrument Panel - Passenger (LHD) (Remove and Replace)

Correction code 18100042 1.38 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning

This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Open LH front door
Lower LH and RH front windows
Move LH front seat backward
Remove LH IP end cap

Note
7x clips, 1x datum, Ensure clip at IP carrier is released fully before removal
Remove LH mid A-pillar trim

Note
2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim
Remove IP LH mid panel

Note
6x tabs
Remove LH sun visor bezel

Note
6x clips, 5x tabs, Release clips, then slide bezel towards front of vehicle to release
Remove bolts securing LH upper A-pillar to body

Note
2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Discard nut after removal
Remove LH upper A-pillar from vehicle

Note
1x connector, 2x datums, 6x clips, Release clips and rotate pillar inboard to access connector, Release datums upward out of IP sub assembly
Adjust steering column fully rearward and fully down

Note
Via UI > Controls > Steering , Use left steering wheel scroll wheel to adjust steering column
Open RH front door
Move RH front seat backward
Open hood

Note
Via center display > Controls > Frunk Open
Power off vehicle via center display

Note
Controls > Safety & Security > Power Off
Remove rear underhood apron

Note
11x clips, 2x datums
Disconnect LV battery connector and First Responder Loop

Note
2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL
Remove RH IP end cap

Note
3x clips
Remove RH mid A-pillar trim

Note
2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim
Remove RH front sill plate

Note
8x clips, 3x datums
Remove RH lower A-pillar trim

Note
1x bolt, T25, 5 Nm, 2x clips, 1x datum
Remove RH sun visor bezel

Note
6x clips, 1x tab, Release clips, then slide bezel towards front of vehicle to release
Remove bolts securing RH upper A-pillar to body

Note
2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Discard nut after removal
Remove RH upper A-pillar from vehicle

Note
1x connector, 2x datums, Rotate pillar inboard to access connector, Release datums upward out of IP sub assembly
Release phone dock

Note
4x clips, 2x datums, Pull up at bottom and swing out from under instrument panel
Remove phone dock

Note
3x connectors, 1x clip, Take caution to release connector locks before pulling straight out of each socket to avoid damage
Release IP service panel

Note
2x tabs, 4x datums, Release top tabs and slide rearward
Release diagnostic and CAN harnesses from IP service panel

Note
2x clips
Remove IP service panel

Note
1x connector
Remove center display bracket bolts

Note
2x bolts, 10mm, 11.5 Nm
Remove center display shroud

Note
3x tabs, Slide display outwards until shroud fully clears IP and support, Release the bottom tabs and pull upward
Release center display coax and power connectors

Note
2x connectors, 1x clip, Slide display rearward outwards from IP bracket and support during connector release
Remove center display

Note
Slide rearward, Place on soft clean surface
Remove IP closeout panel

Note
4x tabs
Remove IP RH mid Panel

Note
14x tabs, 2 datums
Remove IP Decor

Note
21x clips, 6x datums, 4x connectors, Release each IP decor connector clip from IP carrier then disconnect from IP harness
Remove RH front floor mat
Remove RH footwell cover

Note
3x magnets, 1x connector, 4x datums
Remove RH console side carpet

Note
11x clips, 2x datums
Remove fasteners securing RH knee air bag assembly to vehicle

Note
2x bolts, 10mm, 8 Nm, 1x clip
Remove the RH knee air bag assembly from vehicle

Note
2x connectors, 1x clip, 6x tabs
Release glove box

Note
5x screws, T20, 3 Nm
Release glove box connectors

Note
3x connectors
Remove USB outlet

Note
2x screws, T20, 3 Nm, 1x clip
Remove glove box
Release passenger IP air duct temperature sensor connector

Note
1x connector
Remove passenger IP air duct

Note
2x push-pull rivets
Remove IP carrier cross beam screws

Note
2x bolts, 10mm, 3 Nm
Release passenger IP airbag connectors

Note
3x connectors, Pull down spring loaded locks simultaneously to release airbag connectors
Release RH lower instrument panel

Note
3x screws, T20, 3 Nm
Release center lower instrument panel

Note
6x screws, T20, 3 Nm
Release LH lower instrument panel

Note
3x screws, T20, 3 Nm
Release instrument cluster harness

Note
1x connector, 1x clip
Release IP trim harness

Note
1x connector, 1x clip
Position lower instrument panel assembly away from IP sub-assembly

Note
6x datums, Move top edge as far rearward as possible without excessive stress on assembly
Release IP ground harness

Note
1x clip, 1x bolt, 10mm, 9 Nm, Note routing behind center display RH bracket
Remove IP sub-assembly

Note
Slide IP sub-assembly rearward, Lift assembly up from IP carrier, Ensure airwave vents and passenger air bag are clear of lower IP assembly, Remove assembly out through RH front door, Recommend assistance as needed
Release air wave ventilation connectors

Note
4x connectors, Place IC sub-assembly upside down on a protective surface to access connectors
Release aero glass assembly from IP sub-assembly

Note
5x screws, T20, 2.5 Nm
Rotate aero glass assembly from IP sub-assembly

Note
8x tabs, Rotate IP sub-assembly forward to release tabs
Remove aero glass assembly from IP sub-assembly
Remove passenger vent assembly

Note
4x screws, T20, 2 Nm
Install passenger vent assembly

Note
4x screws, T20, 2 Nm
Position aero glass assembly into IP sub-assembly

Note
8x tabs, Align 8 tabs from IP sub-assembly into aero lens assembly
Rotate aero glass assembly to IP sub-assembly

Note
8x tabs, Rotate IP sub-assembly rearward to engage tabs
Secure aero glass assembly to IP sub-assembly

Note
5x screws, T20, 2.5 Nm
Secure air wave ventilation connectors

Note
4x connectors
Install IP sub-assembly

Note
4x datums, Slide IP sub-assembly into vehicle, Ensure passenger air bag and driver vent assembly have clearance past lower IP assembly, Engage IP sub-assembly datums into dash slots, Recommend assistance
Secure IP ground harness

Note
1x clip, 1x bolt, 10mm, 3.5 Nm, Note routing behind center display RH bracket
Secure IP trim harness

Note
1x connector, 1x clip
Secure instrument cluster harness

Note
1x connector
Position lower instrument panel assembly into IP sub-assembly
Secure LH lower instrument panel

Note
3x screws, T20, 3 Nm
Secure center lower instrument panel

Note
6x screws, T20, 3 Nm
Secure RH lower instrument panel

Note
3x screws, T20, 3 Nm
Install IP carrier cross beam bolts

Note
2x bolts, 10mm, 3 Nm
Secure passenger IP airbag connectors

Note
3x connectors
Install passenger IP air duct

Note
2x push-pull rivets
Secure passenger IP air duct temperature sensor connector

Note
1x connector
Install IP Decor

Note
21x clips, 6x datums, 4x connectors, Connect ambient bright harness, Secure each IP decor connector clip to IP carrier, Secure IP decor to lower instrument panel
Secure USB outlet

Note
2x screws, T20, 2 Nm, 1x clip, Ensure USB socket flush in glove box
Secure glove box connectors

Note
3x connectors, Route harness through glove box datums
Install glove box

Note
5x screws, T20, 3 Nm
Install RH knee air bag assembly into vehicle

Note
2x connectors, 6x tabs, 1x clip, Hook tabs before fully seating, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector
Install fasteners securing RH knee air bag assembly to vehicle

Note
2x bolts, 10mm, 8 Nm, 1x clip
Install RH console side carpet

Note
11x clips, 2x datums
Install RH footwell cover

Note
3x magnets, 4x datums, 1x connector
Install RH lower A-pillar trim

Note
1x bolt, T25, 5 Nm, 2x clips, 1x datum
Install RH front sill plate

Note
8x clips, 3x datums
Install RH front floor mat
Install RH upper A-pillar to vehicle

Note
1x connector, 2x datums, Secure RH upper A-pillar harness, Align datums into IP sub assembly, Rotate upper A-pillar panel into position
Install bolts securing RH upper A-pillar to body

Note
2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Install new nut
Install RH sun visor bezel

Note
6x clips, 1x tab, Insert tab and slide bezel towards rear of vehicle, then secure clips
Install RH mid A-pillar trim

Note
2x clips, 3x datums, Verify weather seal is seated properly
Install RH IP end cap

Note
3x clips
Install IP RH mid Panel

Note
14x tabs, 2 datums
Install IP closeout panel

Note
4x tabs
Route display harness behind LH display bracket
Secure center display coax and power connectors

Note
2x connectors, 1x clip, Ensure strain relief clip is secure to linkage arm, Replace clip if damaged
Install center display shroud

Note
3x tabs, Slide display downward until shroud tabs fully engages
Secure center display to IP carrier

Note
2x bolts, 10mm, 11.5 Nm, Slide center display into IP carrier, Start RH bolt first
Secure IP service panel connector

Note
1x connector
Secure diagnostic and CAN harnesses to IP service panel

Note
2x clips
Install IP service panel

Note
2x tabs, 4 datums, Slide forward engaging datums then secure tabs upward into IP
Install phone dock connections

Note
3x connectors, 1x clip
Install phone dock

Note
2x datums, 4 tabs, Slide datums forward into IP and secure tabs down into center console
Connect First Responder Loop and LV battery connector

Note
2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage upper locking tab when fully seated
Install rear underhood apron

Note
11x clips, 2x datums
Close hood
Move RH front seat to original position
Close RH front door
Install LH upper A-pillar to vehicle

Note
1x connector, 2x datums, 6x clips, Secure LH upper A-pillar harness, Align datums into IP sub assembly, Rotate upper A-pillar panel into position engaging clips fully
Install bolts securing LH upper A-pillar to body

Note
2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Install new nut
Install LH sun visor bezel

Note
6x clips, 5x tabs, Insert tabs and slide bezel towards rear of vehicle, then secure clips
Install IP LH mid panel

Note
6x tabs
Install LH mid A-pillar trim

Note
2x clips, 3x datums, Insert mid A-pillar trim into lower A-pillar trim, Secure clips into upper A-pillar and IP sub assembly, Verify weather seal is seated properly
Install LH IP end cap

Note
7x clips, 1x datum
Adjust steering column back to original position

Note
Via UI>Controls>Steering , Use left steering wheel scroll wheel to adjust steering column
Move LH front seat to original position
Calibrate the rear doors.

Note
If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
Raise LH and RH front windows
Close LH front door