05/07/2022 15:51:59

Bracket - Racetrack - Spine - LH (Remove and Replace)

Correction code 15189502 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH front doors.
  2. Lower the LH and RH front windows.
  3. Open the LH and RH falcon wing doors.
  4. Move the LH front seat rearward.
  5. Remove the LH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  6. Remove the bolts (x2), screw, and nut that attach the LH upper A-pillar trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Discard the nut after removal.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm hex
    • 13 mm hex
    • Flex head ratchet/flex head torque wrench
    • Torx T20 socket
  7. Move the LH upper A-pillar trim to access the headliner.
  8. Remove the screw that attaches the LH front end of the headliner to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • Flex head ratchet/flex head torque wrench
    • Torx T20 socket
  9. Move the LH front seat forward.
  10. Release the LH front door seal from the B-pillar trim.
  11. Remove the LH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  12. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  13. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  14. Remove the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  15. Open the liftgate.
  16. Fold the LH 3rd row seat downwards.
  17. Release the clips (x4) that attach the LH trunk sill side trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Plastic trim tool
  18. Remove the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  19. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  20. Open the LH and RH side rear coat hooks.
    Informational PurposesAn informational icon, calling your attention
    Note
    Press the coat hooks inward, and then release to open.
  21. Remove the screws (x2) that attach the LH and RH rear coat hooks to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • Ratchet/torque wrench
    • Torx T20 socket
  22. Partially release the clips (x11) that attach the LH headliner to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Clip pry tool
    • Plastic trim tool
  23. Remove the LH front racetrack trim. See Racetrack Trim - Front - LH (Remove and Replace).
  24. Remove the LH rear racetrack trim. See Racetrack Trim - Rear - LH (Remove and Replace).
  25. Remove the LH falcon wing door primary strut covers (x2).
  26. Remove the LH upper racetrack trim. See Racetrack Trim - Upper - LH (Remove and Replace).
  27. Remove the bolts (x3) that attach the LH spine racetrack bracket to the vehicle, and then remove the bracket from the vehicle.

Install

  1. Position the LH spine racetrack bracket on the vehicle, and then install the bolts (x3) that attach the bracket to the vehicle.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • ¼ in to 3/8 in adapter
    • Flex head ratchet/flex head torque wrench
    • Plastic trim tool
    • Ratchet/torque wrench
    • Torx T40 socket
  2. Install the LH upper racetrack trim. See Racetrack Trim - Upper - LH (Remove and Replace).
  3. Ensure that the LH falcon wing door seal is seated behind the LH upper racetrack trim.
  4. Install the LH falcon wing door primary strut covers (x2).
  5. Install the LH rear racetrack trim. See Racetrack Trim - Rear - LH (Remove and Replace).
  6. Ensure that the falcon wing door seal is seated behind the LH rear racetrack trim.
  7. Install the LH front racetrack trim. See Racetrack Trim - Front - LH (Remove and Replace).
  8. Ensure that the falcon wing door seal is seated behind the LH front racetrack trim
  9. Install the clips (x11) that attach the LH headliner to the vehicle.
  10. Install the screws (x2) that attach the LH and RH rear coat hooks to the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Torx T20 socket
  11. Close the LH and RH side rear coat hooks.
  12. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  13. Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  14. Install the clips (x4) that attach the LH trunk sill side trim to the vehicle.
  15. Move the LH 3rd row seat to original position.
  16. Close the liftgate.
  17. Install the screw that attaches the LH front end of the headliner to the vehicle.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
    • Torx T20 socket
  18. Install the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  19. Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  20. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  21. Install the LH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  22. Fully seat the LH front door seal on the B-pillar trim.
  23. Move the LH front seat rearward.
  24. Position the LH upper A-pillar trim for installation.
  25. Install the bolts (x2) that attach the LH upper A-pillar trim to the vehicle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm hex
    • Flex head ratchet/flex head torque wrench
  26. Install the screw that attaches the LH upper A-pillar trim to the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • Torx T20 socket
  27. Install the nut that attaches the LH upper A-pillar trim to the vehicle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Install a new nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • 13 mm hex
    • Flex head ratchet/flex head torque wrench
  28. Install the LH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  29. Move the LH front seat to original position.
  30. Close the LH and RH falcon wing doors.
  31. Raise the LH and RH front windows.
  32. Close the LH and RH front doors.