01/04/2024 14:46:49

Headlights - Adjust - NA (Wall Method)

Correction code 17400100 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-04-01: Updated measurements and units.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Procedure

  1. Apply tape to wall 33.4 in (84.9 cm) from the ground.
  2. Apply tape to floor 25 ft (7.62 m) from the wall.
  3. Park vehicle on flat level surface perpendicular to wall and align front fascia with tape on floor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Choose a dark work area with low ambient lighting for best results, Ensure tire pressure is set to specification.
  4. Switch headlights ON through UI.
    Informational PurposesAn informational icon, calling your attention
    Note
    Via center display > Controls > Lights > Headlights .
  5. Set vehicle ride height to "Standard".
    Informational PurposesAn informational icon, calling your attention
    Note
    Via center display > Controls > Suspension > Standard, Ensure all tire pressures are set to specification to ensure accurate ride height.
  6. Set air suspension into "Jack Mode".
    Informational PurposesAn informational icon, calling your attention
    Note
    Via center display > Controls > Service > Jack Mode.
  7. Open hood.
    Informational PurposesAn informational icon, calling your attention
    Note
    Via center display > Controls > Frunk Open.
  8. Remove rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips.
  9. Remove LH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums, Remove brush clip at hinge cover first, Take note of clip at headlamp.
  10. Remove RH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums, Remove brush clip at hinge cover first, Take note of clip at headlamp.
  11. Clean headlamps.
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow 1 minute dry time.
  12. Use a fender protector to completely cover the RH headlight.
  13. Adjust LH beam level using headlamp adjuster .
    Informational PurposesAn informational icon, calling your attention
    Note
    Turn adjuster counterclockwise to raise and clockwise to lower beam level, Adjust so that top left part of beam aligns with tape mark on wall, Do not sit in vehicle as this will affect headlamp height.
  14. Remove the fender protector from the RH headlight, and then completely cover the LH headlight with the fender protector.
  15. Adjust RH beam level using headlamp adjuster.
    Informational PurposesAn informational icon, calling your attention
    Note
    Turn adjuster counterclockwise to raise and clockwise to lower beam level, Adjust so that top right part of beam aligns with tape mark on wall, Do not sit in vehicle as this will affect headlamp height.
  16. Remove the fender protector from the LH headlight.
  17. Install LH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2 datums.
  18. Install RH underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums.
  19. Install rear underhood apron.
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips.
  20. Close hood.
  21. Switch headlights to AUTO through UI.
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > Lights > Headlights .
  22. Remove air suspension from "Jack Mode".
    Informational PurposesAn informational icon, calling your attention
    Note
    Using center display > Controls > Service > ''Jack Mode''.