10/12/2024 13:20:20

Glass - Rear Quarter - LH (Remove and Replace)

Correction code 10203002 0.78 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2024-12-10: Added new caution about Pre-Installation Glass Inspection service requirements.
  • 2023-08-04: Added step to cut triangle into urethane applicator tip.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
For Europe only: Only technicians who have been trained in working with diisocyanates and have completed all required certification courses are permitted to perform procedures using urethane and other products containing diisocyanates. Proper personal protective equipment (PPE) must be worn when working with products containing diisocyanates.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in Pre-Installation Glass Inspection before beginning this procedure.

Remove

  1. Open the liftgate.
  2. Open the LH rear door.
  3. Fold the LH 3rd row seat down.
  4. Remove the LH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  5. Remove the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  6. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  7. Apply tape to the vehicle body around the LH rear quarter glass.
  8. Prepare the glazing wire and the T-handles.
  9. Cut the urethane, and then remove the LH rear quarter glass from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    x3 locator clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    When using the glazing wire, start from the rear of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a blade (equalizer blade, equalizer blade handle, and equalizer hydroblade) as needed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove any broken locator clips from the vehicle interior.
  10. Clean excess urethane from the LH quarter panel with Isopropyl Alcohol (IPA).

Install

  1. Apply primer to the mating surface of the LH rear quarter glass.
  2. Apply primer to the inside portion of LH rear quarter glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Allow time for the primer to dry before continuing.
  3. Cut a triangle into the urethane applicator tip approximately 8 mm wide and 14 mm tall, and then prepare the urethane into the caulking gun.
  4. Apply urethane onto the LH rear quarter glass.
    Informational PurposesAn informational icon, calling your attention
    Note
    Betaseal Express has a drive away time of one hour.
  5. Install the LH rear quarter glass onto the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    x3 locator clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply tape to the rear quarter glass to secure it while the urethane cures.
  6. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  7. Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  8. Install the LH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  9. Raise the LH 3rd row seat back into the upright position.
  10. Remove the tape from the rear quarter glass area after the urethane has properly cured.
  11. Close the LH rear door.
  12. Close the liftgate.