12/01/2023 14:14:18

Shroud - Lower - Steering Column (Remove and Replace)

Correction code 32051202 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH front doors.
  2. Lower the LH and RH front windows.
  3. Remove the LH and RH middle A-pillar trims. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  4. Remove the LH and RH instrumental panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
  5. On the vehicle touchscreen, touch Controls > Steering, and then use the left steering wheel scroll wheel to adjust steering column fully rearwards, and downwards.
  6. Disconnect LV power. See LV Power (Disconnect and Connect).
  7. Remove the center console phone dock. See Phone Dock - Center Console (Remove and Replace).
  8. Remove the instrument panel service panel. See Service Panel - Instrument Panel (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the cabin temperature sensor fan from the service panel.
  9. Remove the touchscreen. See Touchscreen (HW3) (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the display mechanism from the touchscreen after the assembly has been removed from the instrument panel.
  10. Release the tabs (x4) that attach the instrument panel closeout panel to the instrument panel, and then remove the closeout panel from the instrument panel.
  11. Remove the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  12. Remove the main instrument panel decor. See Decor - Instrument Panel - Main (Remove and Replace).
  13. Remove the steering yoke/wheel. See Steering Yoke/Wheel (Remove and Replace).
  14. Remove the steering column upper shroud. See Shroud - Upper - Steering Column (Remove and Replace).
  15. Remove the screws (x2) that attach the steering column lower shroud to the steering column.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Ratchet/torque wrench
    • Torx T20 socket
  16. Release the clip that attaches the steering column lower shroud to the steering column, slide the lower shroud rearwards to release the datum, and then remove the lower shroud from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool

Install

  1. Position the steering column lower shroud on the vehicle, and then install the clip that attaches the lower shroud to the steering column.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the lower shroud forwards to engage the datum.
  2. Install the screws (x2) that attach the steering column lower shroud to the steering column.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Ratchet/torque wrench
    • Torx T20 socket
  3. Install the steering column upper shroud. See Shroud - Upper - Steering Column (Remove and Replace).
  4. Install the steering yoke/wheel. See Steering Yoke/Wheel (Remove and Replace).
  5. Install the main instrument panel decor. See Decor - Instrument Panel - Main (Remove and Replace).
  6. Remove the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  7. Position the instrument panel closeout panel on the instrument panel, and then install the tabs (x4) that attach the closeout panel to the instrument panel.
  8. Install the touchscreen. See Touchscreen (HW3) (Remove and Replace).
  9. Install the instrument panel service panel. See Service Panel - Instrument Panel (Remove and Replace).
  10. Connect LV power. See LV Power (Disconnect and Connect).
  11. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
  12. Install the center console phone dock. See Phone Dock - Center Console (Remove and Replace).
  13. On the vehicle touchscreen, touch Controls > Steering, and then use the left steering wheel scroll wheel to adjust the steering column into original position.
  14. Install the LH and RH instrumental panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
  15. Install the LH and RH middle A-pillar trims. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  16. Raise the LH and RH front windows.
  17. Close the LH and RH front doors.