14/07/2022 08:44:30

Actuator - Duct - Floor - 2nd Row (Remove and Replace)

Correction code 18109712 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the RH front door.
  2. Move the front passenger seat rearward.
  3. Remove the RH front floor mat.
  4. Remove the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  5. Remove the RH center console side panel carpet. See Carpet - Side Panel - Center Console - LH (Remove and Replace)
  6. Disconnect the center console USB and rear touchscreen electrical connectors.
  7. Release the clips (x3) that attach the center console harness to the instrument panel carrier and HVAC assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Datums (x2) located at the umbrella inline connection bracket to HVAC assembly.
  8. Loosen the bolt that attaches the RH center console lower bracket to the IP carrier.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Loosen the bolt enough to remove the 2nd row floor duct actuator.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  9. Disconnect the 2nd row floor duct actuator electrical connector.
  10. Remove the screws (x2) that attach the 2nd row floor duct actuator to the vehicle, and then remove the actuator from the vehicle.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Take note of the direction of the keyed socket upon removal.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket

Install

  1. Position the 2nd row floor duct actuator into the vehicle, and then install the screws (x2) that attach the actuator to the vehicle.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Note the keyed socket angle upon installation matches the actuator.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  2. Connect the 2nd row floor duct actuator electrical connector.
  3. Tighten the bolt that attaches the RH center console lower bracket to the IP carrier.
    10 Nm (7.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the bolt does not interfere with the actuator.
  4. Secure the clips (x3) that attach the center console harness to the instrument panel carrier and HVAC assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Datums (x2) located at the umbrella inline connection bracket to HVAC assembly.
  5. Connect the center console USB and rear touchscreen electrical connectors.
  6. Install the RH center console side panel carpet. See Carpet - Side Panel - Center Console - LH (Remove and Replace)
  7. Install the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  8. Install the RH front floor mat.
  9. Close the RH front door.