01/04/2024 14:00:46

Actuator - Pitch Latch - 2nd Row Seat - LH (6 Seat) (Remove and Replace)

Correction code 13020212 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH front door and lower the front windows.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Move the driver seat forward.
  4. Open the LH falcon wing door.
  5. Move the LH 2nd row seat forward.
  6. Disconnect LV power. See LV Power (Disconnect and Connect).
  7. Release the clips (x11) that attach the LH 2nd row seat seat back cover to the seat assembly, disconnect the electrical connector, and then remove the seat back cover from the seat assembly.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to damage the switch harness. Do not remove the trim from the seat assembly until the connector has been disconnected.
    Informational PurposesAn informational icon, calling your attention
    Note
    Start from the top portion of trim and work downward.
  8. Disconnect the LH 2nd row seat OBSB heat pad electrical connector, and then release the clip that attaches the connector to the seat assembly.
  9. Release the Velcro strips (x3) that attach the lower front side of the seat back trim to the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Hold the cover up for access.
  10. Disconnect the LH 2nd row seat pitch latch actuator electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the tabs (x2) from both sides of the connector to disconnect.
  11. Release the LH 2nd row seat pitch latch actuator cable from the cable bracket and actuator.
  12. Remove the screws (x3) that attach the LH 2nd row seat pitch latch actuator to the seat assembly, and then remove the actuator from the assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket

Install

  1. Position the LH 2nd row seat pitch latch actuator into the seat assembly, and then install the screws (x3) that attach the actuator to the seat assembly.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
  2. Install the LH 2nd row seat pitch latch actuator cable into the cable bracket and actuator.
  3. Connect the LH 2nd row seat pitch latch actuator electrical connector.
  4. Position the lower front side of the seat back trim onto the seat frame and secure the Velcro strips (x3).
  5. Position the LH 2nd row seat OBSB heat pad electrical connector onto the seat back assembly, secure the clip that attaches the connector to the seat assembly, and then connect the connector.
  6. Position the LH 2nd row seat seat back cover onto the seat assembly, connect the electrical connector, and then secure the clips (x11) that attach the seat back cover to the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the lower datums and side tabs along the seat assembly, and then engage the clips fully.
  7. Connect LV power. See LV Power (Disconnect and Connect).
  8. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Close the hood.
  10. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors
  11. Move the LH 2nd row seat to the original position.
  12. Move driver seat to the original position.
  13. Connect a laptop with Toolbox 3 to the vehicle.
  14. In Toolbox, click the Actions tab, and then search for "BCS2L".
  15. Click PROC_BCS2L_R2-L_CALIBRATE-S2L-PITCHvia Toolbox: (link), and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click the X at the top right corner of the window to close once complete.
  16. Click PROC_BCS2L_R2-L_CALIBRATE-S2L-TRACKvia Toolbox: (link), and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click the X at the top right corner of the window to close once complete.
  17. Disconnect Toolbox and remove the laptop from the vehicle.
  18. Raise the front windows and close the LH front door.