Correction code 13022702 2.40 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

1. Open all four doors
2. Lower LH and RH front windows
3. Remove the LH 2nd row seat from the vehicle. See Seat Assembly - 2nd Row - LH (Without 2nd Row Bench Seats) (Remove and Replace).
4. Remove LH monopost seat back cover
   Note

   11x clips, 1x connector, Start from top portion of trim and work your way down, Be cautious of switch harness, do not rip trim away

   

   

   

5. Remove bolts securing 2nd row LH monopost under belly trim
   Note

   2x bolts, 10mm, 8 Nm

   

   

6. Release clips securing 2nd row LH monopost under belly trim
   Note

   4x clips, Use caution when release lower trim as comfort seat switch harness is short in length

   

   

7. Disconnect and remove 2nd row LH monopost under belly trim
   Note

   1x connector

   

8. Remove 2nd row monopost surround carpets from surround trim
   Note

   Carpets are one time use, Discard after removal

   

   

9. Remove screws securing magic carpet
   Note

   2x screws, T20, 2.5 Nm

   

10. Remove magic carpet from plate assembly
    Note

    2x plastic guides

    

    

11. Release 2nd row LH monopost top inner covers to gain access to rear strip
    Note

    8x tabs, Be cautious when releasing trim to avoid damage, tabs are brittle

    

    

12. Remove rear strip from 2nd row LH monopost seat
    Note

    6x tabs, Be cautious when releasing trim to avoid damage, tabs are brittle

    

    

    

    

13. Release front strip from 2nd row LH monopost seat
    Note

    4x tabs, Be cautious when releasing trim to avoid damage, tabs are brittle

    

    

14. Release seat harness from substrate
    Note

    2x clips

    

    

15. Remove bolts securing front side of podium substrate
    Note

    2x bolts, T25, 3 Nm

    

    

16. Slightly raise trim covering front seat base support
    Note

    Front end of LH surround, RH surround and front substrate

    

17. Remove screw securing 2nd row LH monopost seat front base support
    Note

    1x T25, 5 Nm

    

18. Remove 2nd row LH monopost seat front base support
    Note

    Slightly lift up on trim panels to gain access, While sliding forward slightly rotate front of base support upward to remove

    

    

19. Install 2nd row LH monopost seat front base support
    Note

    Slightly lift up on trim panels to gain access, Slightly rotate front of base support downward then slide inward to install

    

    

20. Install screw securing 2nd row LH monopost seat front base support
    Note

    1x T25, 5 Nm

    

21. Secure trim covering front seat base support
    Note

    Front end of LH surround, RH surround and front substrate, Front strip will be secured at later step

    

22. Install bolts securing podium substrate
    Note

    4x bolts, T25, 3 Nm

    

    

23. Secure seat harness onto substrate
    Note

    2x clips

    

    

24. Install front strip onto 2nd row LH monopost seat
    Note

    4x tabs

    

    

25. Install rear strip onto 2nd row LH monopost seat
    Note

    5x tabs

    

    

    

    

26. Secure 2nd row LH monopost top inner covers
    Note

    8x tabs

    

    

27. Install magic carpet onto plate assembly
    Note

    2x plastic guides, Align guides into surround trim channels

    

    

28. Install screws securing magic carpet
    Note

    2x screws, T20, 2.5 Nm

    

29. Install 2nd row monopost surround carpets onto surround trim
    Note

    Carpets are one time use, Install new carpet

    

    

30. Connect 2nd row LH monopost under belly trim
    Note

    1x connector

    

31. Secure 2nd row LH monopost under belly trim
    Note

    4x clips, Align datums then secure panel

    

32. Install bolts securing 2nd row LH monopost under belly trim
    Note

    2x bolts, 10mm, 8 Nm

    

    

33. Install LH 2nd row seat back cover
    Note

    11x clips, 1x connector, Align lower datums and side tabs along seat assembly, Then engage clips to fully secure

    

    

    

34. Install the LH 2nd row seat. See Seat Assembly - 2nd Row - LH (Without 2nd Row Bench Seats) (Remove and Replace).
35. Raise LH and RH front windows
36. Close LH front door