15/10/2023 20:32:29

Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace)

Correction code 13050062 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open all the doors and lower the front windows.
  2. Move the front seats fully forward.
  3. Move the LH and RH 2nd row seats fully forward.
  4. Remove the LH and RH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  5. Apply masking tape to the RH racetrack to avoid damage.
  6. Remove the RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  7. Remove the RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  8. Remove the RH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  9. Repeat step 6 through step 11 8 for the LH side of the vehicle.
  10. Move the LH and RH 2nd row seats rearward and out of easy entry position.
  11. Remove the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (7 Seat) (Remove and Replace).
  12. Move the LH and RH 2nd row seats fully forward.
  13. Remove the 2nd row rear floor panel. See Floor Panel - Rear - 2nd Row (7 Seat) (Remove and Replace).
  14. Remove and discard the bolts (x6) that attach the rear of the RH 2nd row seat track to the vehicle.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 11 mm socket
  15. Move the LH 2nd row seat fully rearwards.
  16. Release the clip that attaches the RH inner front plate carpet assembly to the vehicle, and then remove the plate from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully peel up the front plate carpet decal to release it from the seat track base.
  17. Release the clip that attaches the RH outer front plate carpet assembly to the vehicle, and then remove the plate from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully peel up the front plate carpet decal to release it from the seat track base.
  18. Remove and discard the bolts (x6) that attach the front of the RH 2nd row seat track to the vehicle.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 11 mm socket
  19. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  20. Disconnect LV power. See LV Power (Disconnect and Connect).
  21. Disconnect the RH 2nd row seat harness connectors (x3).
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the bracket for better access.
  22. Release the clips (x2) that attach the RH 2nd row seat harness to the RH floor support bracket.
  23. Fold the RH 2nd row seat to the down position.
  24. With assistance, remove the RH 2nd row seat assembly from the vehicle.

Install

  1. With assistance, position the RH 2nd row seat assembly into the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the guide pins are aligned properly.
  2. Move the seat back to the upright position.
  3. Install and hand tighten new bolts (x6) that attach the front of the RH 2nd row seat track to the vehicle.
  4. Secure the clips (x2) that attach the RH 2nd row seat harness to the RH floor support bracket.
  5. Connect the RH 2nd row seat harness connectors (x3).
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the connector housing bracket if released.
  6. Connect LV power. See LV Power (Disconnect and Connect).
  7. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  8. Move the RH 2nd row seat fully forward.
  9. Install new bolts (x6) that attach the rear of the RH 2nd row seat track.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Tighten the center bolt on both sides before tightening the outer bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 11 mm socket
  10. Install the 2nd row rear floor panel. See Floor Panel - Rear - 2nd Row (7 Seat) (Remove and Replace).
  11. Move the RH 2nd row seat rearward and out of easy entry position.
  12. Tighten the bolts (x6) that attach the front of the RH 2nd row seat track to the vehicle.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Tighten the foremost bolt on each side before the outer bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 11 mm socket
  13. Position the RH outer front plate carpet assembly into the vehicle, and then secure the clip that attaches the plate to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the front plate carpet decal onto the seat track base to cover the fastener.
  14. Position the RH inner front plate carpet assembly into the vehicle, and then secure the clip that attaches the plate to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the front plate carpet decal onto the seat track base to cover the fastener.
  15. Move the RH 2nd row seat rearward and out of easy entry position.
  16. Install the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (7 Seat) (Remove and Replace).
  17. Move the 2nd row seats fully forward.
  18. Install the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  19. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  20. Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  21. Repeat step 18 through step 20 for the RH side of the vehicle.
  22. Install the LH and RH side rear trunk garnish. See Garnish - Rear Trunk - Side - LH (Remove and Replace).
  23. Close the liftgate.
  24. Move 2nd row seats to the original positions.
  25. Close the RH front door.
  26. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
  27. Move the driver seat to the original position.
  28. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  29. Click the Actions tab, and then search for "Service-Redeploy".
  30. Click SERVICE CAN REDEPLOY, and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    The routine will state pass but the update will continue to run in the background.
    Informational PurposesAn informational icon, calling your attention
    Note
    The UI will show the update progress.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click the X at the top right of window to close once complete.
  31. Disconnect Toolbox and remove the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  32. Raise the front windows and close the LH front door.