13/10/2022 12:59:38

Cable - Recliner - 2nd Row - RH (5 Seat) (Remove and Replace)

Correction code 13052702 1.74 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the RH 2nd row seat seat back sub-assembly. See Seat Back Sub-Assembly - 2nd Row Seat - RH (5 Seat) (Remove and Replace).
  2. Remove the clips (x4) and screw that attach the upper and lower inner recliner covers to the seat assembly, and then remove the covers from the seat assembly.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  3. Release the clip, tab and eyelet that attach the RH 2nd row recliner cable to the recliner assembly and cushion tube.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the keyed cable counterclockwise to remove from the recliner release arm eyelet.
  4. Release the clips (x2) that attach the RH 2nd row recliner cable to the rear of the seat cushion frame.
  5. Release the clips (x2) that attach the RH 2nd row recliner cable to the front of the seat cushion frame.
  6. Remove the screws (x2) that attach the RH 2nd row seat recliner cable compensator housing to the cushion support, and then release the housing from the cushion support.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the compensator housing down and out of the cushion support.
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  7. Remove the bolts (x2) that attach the RH 2nd row seat recliner cable spindle assembly to the seat cushion frame, and then remove the recliner cable from the seat assembly.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Position the RH 2nd row seat recliner cable spindle assembly into the seat cushion frame, and then install the bolts (x2) that attach the recliner cable to the seat assembly.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  2. Position the RH 2nd row seat recliner cable compensator housing to the cushion support, and then install the screws (x2) that attach the housing to the cushion support.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the compensator housing down and out of the cushion support.
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  3. Install the clips (x2) that attach the RH 2nd row recliner cable to the front of the seat cushion frame.
  4. Install the clips (x2) that attach the RH 2nd row recliner cable to the rear of the seat cushion frame.
  5. Secure the clip, tab and eyelet that attach the RH 2nd row recliner cable to the recliner assembly and cushion tube.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the keyed cable clockwise to install it to the recliner release arm eyelet.
  6. Position the upper and lower inner recliner covers onto the seat assembly, and then install the clips (x4) and screw that attach the covers to the seat assembly.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  7. Install the RH 2nd row seat seat back sub-assembly. See Seat Back Sub-Assembly - 2nd Row Seat - RH (5 Seat) (Remove and Replace).