Bracket - Racetrack - Header - Rear - LH (Remove and Replace)
Correction code 15189712 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Remove
- Open the LH and RH front doors.
- Lower the LH and RH front windows.
- Open the LH and RH falcon wing doors.
- Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
- Open the liftgate.
- Fold the LH 3rd row seat downwards.
-
Release the clips (x4) that attach the
LH trunk sill side trim to the vehicle.
NoteUse of the following tool(s) is recommended:
- Plastic trim tool
- Remove the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
- Remove the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
- Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
-
Open the LH and RH side rear coat
hooks.
NotePress the coat hooks inward, and then release to open.
-
Remove the screws (x2) that secure the
LH and RH rear coat hooks to the vehicle.
NoteUse of the following tool(s) is recommended:
- 2 in extension
- Ratchet/torque wrench
- Torx T20 socket
-
Partially release the clips (x11) that
attach the LH headliner to the vehicle.
NoteUse of the following tool(s) is recommended:
- Clip pry tool
- Plastic trim tool
- Remove the LH rear racetrack trim. See Racetrack Trim - Rear - LH (Remove and Replace).
-
Remove the bolts (x2) and clip that
secure the LH rear header racetrack bracket to the vehicle, and then remove the bracket
from the vehicle.
NoteUse of the following tool(s) is recommended:
- ¼ in to 3/8 in adapter
- Flex head ratchet/flex head torque wrench
- Plastic trim tool
- Torx T40 socket
Install
-
Position the LH rear header racetrack
bracket on the vehicle, and then install the bolts (x2) and clip that attach the bracket
to the vehicle.NoteUse of the following tool(s) is recommended:
- ¼ in to 3/8 in adapter
- Flex head ratchet/flex head torque wrench
- Plastic trim tool
- Ratchet/torque wrench
- Torx T40 socket
- Install the LH rear racetrack trim. See Racetrack Trim - Rear - LH (Remove and Replace).
-
Ensure that the falcon wing door seal
is seated behind the LH rear racetrack trim.
-
Install the clips (x11) that attach the LH headliner to the vehicle.
-
Install the screws (x2) that secure
the LH and RH rear coat hooks to the vehicle.NoteUse of the following tool(s) is recommended:
- Ratchet/torque wrench
- Torx T20 socket
- Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
-
Close the LH and RH side rear coat
hooks.
- Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
- Install the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
- Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
-
Install the clips (x4) that attach the
LH trunk sill side trim to the vehicle.
- Move the LH 3rd row seat to original position.
- Close the liftgate.
- Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
- Close the LH and RH falcon wing doors.
- Raise the LH and RH front windows.
- Close the LH and RH front doors.