29/05/2024 18:11:42

Bracket - 2nd Row Floor Panel - LH (Without 2nd Row Bench Seats) (Remove and Replace)

Correction code 153036020.50 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Connect a laptop with Toolbox to the vehicle. See Toolbox 3 (Connect and Disconnect).
  2. In Toolbox, click Actions, and then search for ‘BCS2L’.
  3. Click PROC_BCREAR_X_SEAT-INSTALL-MODE-ONvia Toolbox: (link), and then click Run. Allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify that the routine you are selecting is specific to "BCS2L".
    Informational PurposesAn informational icon, calling your attention
    Note
    Click X at the top right of the window to close once completed.
  4. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  5. Move the driver and front passenger seats fully forward.
  6. Remove the LH and RH rear sill panel trims. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  7. Remove the 2nd row floor mat.
  8. Remove the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (6 Seat) (Remove and Replace).
  9. Remove the 2nd row LH seat post inboard and outboard trim. See:
  10. Move the 2nd row LH seat fully backward using the comfort button.
  11. Remove the LH 2nd row seat sliding plate. See Plate - Sliding - Seat - 2nd Row - LH (Remove and Replace).
  12. Release the tabs (x2) that attach the 2nd row LH seat inline harness bracket to the LH 2nd row front floor panel bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the bracket upward.
  13. Remove the bolts (x2) that attach the LH 2nd row LH front floor panel bracket to the vehicle, and then remove the bracket from the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Install the 2nd row LH seat inline harness bracket on the sliding panel base.
    Informational PurposesAn informational icon, calling your attention
    Note
    x2 tabs
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the tabs downward to engage.
  2. Install the bolts (x2) that attach the LH 2nd row LH front floor panel bracket to the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the LH 2nd row seat sliding plate. See Plate - Sliding - Seat - 2nd Row - LH (Remove and Replace).
  4. Install 2nd row LH seat inboard and outboard covers. See:
  5. Move the 2nd row seat back to its original position.
  6. Install the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (6 Seat) (Remove and Replace).
  7. Install the 2nd row floor mat.
  8. Install the LH and RH rear sill panel trims. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  9. Move the driver and front passenger seats back to their original position.
  10. Reconnect a laptop with Toolbox to the vehicle. See Toolbox 3 (Connect and Disconnect).
  11. In Toolbox, click PROC_BCREAR_X_SEAT-INSTALL-MODE-OFFvia Toolbox: (link), and then click Run. Allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify that the routine you are selecting is specific to "BCS2L".
    Informational PurposesAn informational icon, calling your attention
    Note
    Click X at the top right of the window to close once completed.
  12. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).