06/12/2022 10:11:59

Trim - Backrest - Seat - 2nd Row - LH (6 Seat) (Remove and Replace)

Correction code 13081412 2.52 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open all four doors.
  2. Lower the LH and RH front windows.
  3. Remove the LH 2nd row seat assembly. See Seat Assembly - 2nd Row - LH (Without 2nd Row Bench Seats) (Remove and Replace).
  4. Remove the bolts (x2) that attach the 2nd row LH monopost under belly trim to the seat.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Ratchet/torque wrench
  5. Release the clips (x4) that attach the 2nd row LH monopost under belly trim to the seat.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution when releasing the lower trim as the comfort seat switch harness is short in length.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  6. Disconnect the 2nd row LH monopost under belly trim connector, and then remove the trim from the seat.
  7. Remove the bolt, nyloc nut, and seat frame washer that attaches the seatbelt anchor to the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Discard the nyloc nut after removal.
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Socket 3/8in Dr. 11/16 - 1761805-00-A
    • Torx Plus T45 socket
  8. Remove the LH 2nd row seatbelt anchor escutcheon. See Escutcheon - Seatbelt Anchor - 2nd Row - LH (6 Seat) (Remove and Replace).
  9. Remove the LH 2nd row seat seat back cover. See Cover - Seat Back - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
  10. Remove the LH 2nd row seatbelt escutcheon. See Escutcheon - Seatbelt - 2nd Row - LH (6 Seat) (Remove and Replace).
  11. Route the seatbelt through the lower and upper cushions, and then remove the seat back assembly from the seat.
  12. Place the seat back assembly face down on a workbench.
  13. Slowly release the Velcro straps (x5) that attach the LH 2nd row seat backrest trim to the seat back frame.
  14. Remove the staples (x2) that attach the LH 2nd row seat backrest trim to the seat back assembly.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
    • Needle nose pliers
  15. Release the tabs (x2) that attach the LH 2nd row seat backrest trim to the seat back assembly.
  16. Release the J-clips (x2) that attach the LH 2nd row seat backrest trim upper seat back upholstery to the seat back assembly.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Limit the use of the 90 pick only to release the J-clips, as the upholstery could be damaged by poking a hole through it.
    Informational PurposesAn informational icon, calling your attention
    Note
    Using the pick to release the trim from the seat back assembly. Remove the rest by hand.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  17. Rotate the seat back assembly to face upwards.
  18. Release the Velcro that attaches the LH 2nd row seat backrest trim lower seat back upholstery to the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift up on the lower portion of the seat back trim and slowly separate Velcro.
  19. Fold the LH 2nd row seat backrest trim upwards.
  20. Release the hog rings (x4) that attach the LH 2nd row seat backrest trim to the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Cut the hog rings out with diagonal cutters.
    Tip: Use of the following tool(s) is recommended:
    • Diagonal cutters
  21. Fold the LH 2nd row seat backrest trim back to reveal the upper seat back hog rings.
  22. Release the hog rings (x7) that attach the LH 2nd row seat backrest trim to the seat back assembly.
    Tip: Use of the following tool(s) is recommended:
    • Diagonal cutters
  23. Release the Velcro that attaches the LH 2nd row seat backrest trim upper seat back upholstery to the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slowly release the Velcro from the seat back foam.
  24. Remove the LH 2nd row seat backrest trim from the seat back foam.

Install

  1. Position the LH 2nd row seat backrest trim upper seat back upholstery on the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the seat back headrest upholstery seam aligns with the center groove on the seat back head rest foam. Firmly press upholstery headrest Velcro to seat back foam to secure.
  2. Install the hog rings (x7) that attach the LH 2nd row seat backrest trim to the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Starting on the LH side of the foam, install the hog rings working downwards and then upwards to the RH side.
    Tip: Use of the following tool(s) is recommended:
    • Hog ring pliers - 1501599-00-A
  3. Pull the LH 2nd row seat backrest trim upholstery downwards, and then install the hog rings (x4) that attach the trim to the seat back assembly.
    Tip: Use of the following tool(s) is recommended:
    • Hog ring pliers - 1501599-00-A
  4. Pull the remaining LH 2nd row seat backrest trim upholstery downwards, and then firmly press the Velcro into the seat back foam.
    Informational PurposesAn informational icon, calling your attention
    Note
    Thoroughly press the lower seat back Velcro into place until fully secure.
  5. Rotate the seat back assembly to face downwards.
  6. Install the J-clips (x2) that attach the LH 2nd row seat backrest trim upper seat back upholstery to the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Starting on LH side of upper upholstery, firmly press the J-clips into the seat back assembly to secure. Use a plastic trim tool to ensure J-clips are fully seated.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  7. Install the tabs (x2) that attach the LH 2nd row seat backrest trim to the seat back assembly.
  8. Install the Velcro straps (x5) that attach the LH 2nd row seat backrest trim to the seat back frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Firmly pull the Velcro straps to seat back assembly, and then press into place to secure.
  9. Install the staples (x2) that attach the LH 2nd row seat backrest trim to the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the Velcro strap to the seat back assembly with the staples.
  10. Route the seatbelt through the seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the seatbelt anchor escutcheon is routed onto the seatbelt prior to the seatbelt anchor being routed through seat cushion. Do not install seatbelt the anchor escutcheon at this time.
  11. Install the LH 2nd row seatbelt escutcheon. See Escutcheon - Seatbelt - 2nd Row - LH (6 Seat) (Remove and Replace).
  12. Install the LH 2nd row seat seat back cover. See Cover - Seat Back - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
  13. Install the LH 2nd row seatbelt anchor escutcheon. See Escutcheon - Seatbelt Anchor - 2nd Row - LH (6 Seat) (Remove and Replace).
  14. Install the bolt, nyloc nut, and seat frame washer that attaches the seatbelt anchor to the seat frame.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Install a new nyloc nut.
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Socket 3/8in Dr. 11/16 - 1761805-00-A
    • Torx Plus T45 socket
  15. Position the LH monopost under belly trim on the seat assembly, and then connect the trim connector.
  16. Install the clips (x4) that attach the 2nd row LH monopost under belly trim to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the datums first, and then secure the trim.
  17. Install the bolts (x2) that attach the 2nd row LH monopost under belly trim to the seat.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  18. Install the LH 2nd row seat assembly. See Seat Assembly - 2nd Row - LH (Without 2nd Row Bench Seats) (Remove and Replace).
  19. Raise the LH and RH front windows.
  20. Close the LH front door.