13/10/2022 07:14:22

Seat Back Sub-assembly - 2nd Row Seat - RH (7 Seat) (Remove and Replace)

Correction code 13058812 1.56 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace).
  2. Remove the RH 2nd row seat cushion sub-assembly. See Cushion Sub-assembly - 2nd Row Seat - RH (5 Seat) (Remove and Replace).
  3. Remove the RH 2nd row seat inboard side shield. See Side Shield - Inboard - 2nd Row Seat - RH (5 Seat) (Remove and Replace).
  4. Release the J-hook that attaches the RH 2nd row seat back upholstery to the seat assembly.
  5. Unzip the RH 2nd row seat back upholstery on LH and RH sides of the backrest cover, release the Velcro strips (x2) that attach the upholstery to the seat back, and then fold the seat back over the headrest for access.
    Informational PurposesAn informational icon, calling your attention
    Note
    The ends of zippers are tucked underneath the upholstery.
    Tip: Use a pick to help move the zipper.
  6. Release the clips (x5) that attach the RH 2nd row seat back plastic to the seat back assembly, and then remove the seat back plastic from the assembly.
  7. Disconnect the RH 2nd row seat heater and side airbag electrical connectors (x2).
  8. Remove and discard the nuts (x2) that attach the RH 2nd row seat side airbag to the seat assembly, and then release the air bag from the seat assembly.
    20 Nm (14.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the side airbag away from the backrest frame and clear of the mounting studs.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  9. Release the lower portion of the RH 2nd row seat back cushion from the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the harness and tension flaps through the seat back frame.
  10. Lift the RH 2nd row seat seat back sub-assembly from the backrest frame, and then remove the sub-assembly from the seat assembly.

Install

  1. Position the RH 2nd row seat seat back sub-assembly onto the seat assembly, and then maneuver the sub-assembly over the headrest bracket down to the seat controller bracket.
  2. Secure the lower portion of the RH 2nd row seat back cushion from the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Guide the harness and tension flaps through the seat back frame.
  3. Position the RH 2nd row seat side airbag into the seat assembly, and then install new nuts (x2) that attach the air bag to the seat assembly.
    20 Nm (14.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Position the side airbag mounting studs through the backrest frame.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Connect the RH 2nd row seat heater and side airbag electrical connectors (x2).
  5. Position the RH 2nd row seat back plastic to the seat back assembly, and then secure the clips (x5) that attach the seat back plastic to the assembly.
  6. Fold the seat back upholstery into position, secure the Velcro strips (x2), and then zip the upholstery on the LH and RH sides of backrest cover.
    Informational PurposesAn informational icon, calling your attention
    Note
    The ends of zippers are tucked underneath the upholstery.
    Tip: Use a pick to help move the zipper.
  7. Secure the J-hook that attaches the RH 2nd row seat back upholstery to the seat assembly.
  8. Install the RH 2nd row seat inboard side shield. See Side Shield - Inboard - 2nd Row Seat - RH (5 Seat) (Remove and Replace).
  9. Install the RH 2nd row seat cushion sub-assembly. See Cushion Sub-assembly - 2nd Row Seat - RH (5 Seat) (Remove and Replace).
  10. Install the RH 2nd row seat assembly. See Seat Assembly - 2nd Row - RH (7 Seat) (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to redeploy the vehicle firmware after the RH 2nd row seat assembly is reinstalled.