03/08/2022 08:18:11

Racetrack Trim - Front - LH (Remove and Replace)

Correction code 15187302 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH front doors.
  2. Lower the LH and RH front windows.
  3. Open the LH and RH falcon wing doors.
  4. Move the LH front seat rearward.
  5. Remove the LH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  6. Remove the bolts (x2), screw, and nut that attach the LH upper A-pillar trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Discard the nut after removal.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm hex
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • Torx T20 socket
  7. Move the LH upper A-pillar trim to gain access to the headliner.
  8. Remove the screw that attaches the LH front end of the headliner to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Flex head ratchet/flex head torque wrench
    • Torx T20 socket
  9. Move the LH front seat forward.
  10. Release the LH front door seal from the B-pillar trim.
  11. Remove the LH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  12. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  13. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  14. Release the clips (x3) and magnets (x2) that attach the LH upper B-pillar trim to the B-pillar, and then disconnect the LH falcon wing door button electrical connector.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
    • Plastic trim tool
    • Pocket screwdriver
  15. Move the LH upper B-pillar trim aside.
  16. Partially release the clips (x5) that attach the LH front headliner to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
    • Plastic trim tool
  17. Remove the screw that attaches the LH front racetrack trim to the spine racetrack.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • Torx T20 socket
  18. Starting at the bottom of the LH front racetrack trim and working upwards, release the clips (x22) that attach the racetrack trim to the vehicle, and then remove the trim from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
    • Plastic trim tool

Install

  1. Starting at the top of the LH front racetrack trim and working downwards, position the trim on the vehicle, and then install the clips (x22) that attach the trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the top of the racetrack trim is engaged with the spine racetrack.
  2. Install the screw that attaches the LH front racetrack trim to the spine racetrack.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
    • Torx T20 socket
  3. Make sure the LH falcon wing door seal is seated behind the LH front racetrack trim.
  4. Install the clips (x5) that attach the LH front headliner to the vehicle.
  5. Install the screw that attaches the LH front end of the headliner to the vehicle.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
    • Torx T20 socket
  6. Connect the LH falcon wing door button electrical connector, and then install the clips (x3) and magnets (x2) that attach the LH upper B-pillar trim to the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace the clips if damaged.
  7. Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  8. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  9. Install the LH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  10. Fully seat the LH front door seal along the LH B-pillar trims.
  11. Move the LH front seat rearward.
  12. Position the LH upper A-pillar trim for installation.
  13. Install the bolts (x2) that attach the LH upper A-pillar trim to the vehicle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm hex
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  14. Install the screw that attaches the LH upper A-pillar trim to the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
    • Torx T20 socket
  15. Install the new nut that attaches the LH upper A-pillar trim to the vehicle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 2 in extension
    • 13 mm socket
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
  16. Install the LH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  17. Move the LH front seat to original position.
  18. Close the LH and RH falcon wing doors.
  19. Raise the LH and RH front windows.
  20. Close the LH and RH front doors.