23/05/2024 08:24:07

Cover - Rear Access - HV Battery (Remove and Replace)

Correction code 16101022 5.40 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-06-01: Added steps to remove and install the mica insulator panel.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning

Only technicians who have been trained in High Voltage Awareness and have completed all required certification courses (if applicable) are permitted to perform this procedure. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional glove and safety information.

Remove

  1. Move the vehicle to a 2 post lift. See Raise Vehicle - 2 Post Lift.
  2. Perform a cooling system thermal fill drain. See Thermal Fluid - Cooling System (Fill/Drain).
  3. Remove the LH and RH rocker panel moldings. See Molding - Rocker Panel - LH (Remove and Replace).
  4. Position the 2 post lift pads for HV battery removal.
  5. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Install).
  7. Remove the LH and RH sill panel trims. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  8. Remove the 2nd row mid floor panel. See:
  9. Remove the LH and RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  10. Remove the LH and RH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  11. Remove the 2nd row rear floor panel. See:
  12. Remove the bolts (x2) that attach the busbar duct to the body, and then remove the busbar duct from the vehicle.
  13. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  14. Remove the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  15. Remove the trunk side trim bracket. See:
  16. Disconnect LV power. See LV Power (Disconnect and Connect).
  17. Remove the 3rd row seat cushion, if installed. See Cushion - Seat - 3rd Row (Remove and Replace).
  18. Remove the LH inner reinforcement. See Reinforcement - Inner - LH (Remove and Replace).
  19. Remove the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).
  20. Perform Vehicle HV Disablement Procedure. See Vehicle HV Disablement Procedure.
  21. Remove the pyrotechnic battery disconnect. See Pyrotechnic Battery Disconnect (Remove and Replace).
  22. Remove the HV Battery. See HV Battery (AWD) (Remove and Install).
  23. Remove and discard the bolts (x8) that attach the HV battery rear access cover to the HV battery.
    Figure 1. Vehicles built before September 19, 2022
    Figure 2. Vehicles built September 19, 2022 and later
  24. Vehicles built before September 19, 2022 only - Use non-conductive plastic chisels to break the seal and separate the HV battery rear access cover from the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Note
    Be careful not to severely bend or deform the access cover, nor damage the internal components therein.
  25. Vehicles built September 19, 2022 and later only - Remove the HV battery rear access cover.
  26. Vehicles built before September 19, 2022 only - If installed, remove the mica insulator panel from the rear access opening.
    Informational PurposesAn informational icon, calling your attention
    Note
    It may be necessary to crease the panel to remove it from the opening.

Install

  1. Vehicles built September 19, 2022 and later only - Use an IPA wipe to clean the sealing surfaces of the HV battery rear access panel and the rear bay of the HV battery, allow them at least one minute to dry, and then go to step 7.
  2. Vehicles built before September 19, 2022 - Use non-conductive plastic chisels or other non-marring tools to remove the sealant from the HV battery and HV battery rear access cover.
  3. Use an ESD-safe vacuum to remove debris, wipe the sealing surfaces with an alcohol wipe, and then allow to dry.
  4. If removed previously, install the mica insulator panel into the rear access opening.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the mica panel is completely tucked behind the HV battery top cover sheet metal.
    Informational PurposesAn informational icon, calling your attention
    Note
    It may be necessary to crease the panel to install it into the opening.
  5. Load a cartridge of sealant into the caulking gun and cut the tip of the sealant to make a triangle of X mm by Y mm.
  6. Apply the sealant onto the sealing surface of the HV battery in a continuous smooth bead.
  7. Carefully set the HV battery rear access cover onto the HV battery.
    Figure 3. Vehicles built before September 19, 2022
    Figure 4. Vehicles built September 19, 2022 and later
  8. Install new bolts (x8) to attach the HV battery rear access cover to the HV battery, and then tighten the bolts in a criss-cross pattern.
    4.5 Nm (3.3 lbs-ft)
    Figure 5. Vehicles built before September 19, 2022
    Figure 6. Vehicles built September 19, 2022 and later
  9. Measure the voltage across the pyrotechnic battery disconnect mount points, and then install the pyrotechnic battery disconnect. See Pyrotechnic Battery Disconnect (Remove and Replace).
  10. Perform an HV battery air leak test. See HV Battery Air Leak Test (On Table).
  11. Install the HV Battery. See HV Battery (AWD) (Remove and Install).
  12. Install the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).
  13. Install the LH inner reinforcement. See Reinforcement - Inner - LH (Remove and Replace).
  14. Install the 3rd row seat cushion, if previously removed. See Cushion - Seat - 3rd Row (Remove and Replace).
  15. Connect LV power. See LV Power (Disconnect and Connect).
  16. Install the trunk side trim bracket. See:
  17. Install the trunk sill trim. See Trim - Sill - Trunk (Remove and Replace).
  18. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  19. Install the busbar duct to the body, and then install the bolts (x2) that attach the busbar duct to the body.
    2.5 Nm (1.8 lbs-ft)
  20. Install the 2nd row rear floor panel. See:
  21. Install the LH and RH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  22. Install the LH and RH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  23. Install the 2nd row mid floor panel. See:
  24. Install the LH and RH sill panel trims. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  25. Install the underhood storage unit. See Underhood Storage Unit (Remove and Install).
  26. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  27. Install the LH and RH rocker panel moldings. See Molding - Rocker Panel - LH (Remove and Replace).
  28. Hold the LH and RH upper B-pillar buttons in the "Close" position to manually calibrate the LH and RH rear doors.
  29. Remove the vehicle from the 2 post lift. See Raise Vehicle - 2 Post Lift.