Headrest - 3rd Row Seat - LH (Remove and Replace)
Correction code 13064302 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Remove
- Open the LH and RH falcon wing doors.
- Open the liftgate.
- Fold the 2nd row 40 and 60 seats downward.
- Remove the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
- Remove the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
- Remove the rear trunk carpet. See Carpet - Rear Trunk (5 Seat) (Remove and Replace).
- Fold the LH and RH 3rd row seats downward.
- Remove the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
-
Release the tabs (x4), fir tree clips (x2), and J hook that attach the lower section
of the LH 3rd row seat upholstery to the seat.
NotePull the tabs inward, and then upwards to release.Tip: Use of the following tool(s) is recommended:
- Clip pry tool
-
Disconnect the LH 3rd row seat connectors (x2), and then re-route the connectors
through the lower section of the upholstery.
-
Route the LH 3rd row seat connectors (x2) around the lower section of the upholstery,
and then connect the connectors.
-
Unfold the LH 3rd row seat to original position.
NoteLeave the seat headrest in the folded position.
-
Release the J-hook clip that attaches the upper half of the LH 3rd row seat
upholstery to the seat.
-
From the 3rd row, pull the inner
portion of the seat cover and foam outward to gain access to the LH 3rd row seat
headrest actuator cable.
CAUTIONUse caution to not snag the J-hooks. The actuator is located on the front side of the seat back under the upholstery and cushion assembly.NoteUse the fold function to feed the bottom of the seat upholstery forward.
-
Remove the LH 3rd row seat headrest
actuator cable from the cable tether mount.
NotePry the cable tether outward to release.Tip: Use of the following tool(s) is recommended:
- Clip pry tool
-
Remove the LH 3rd row seat headrest
actuator cable from the actuator.
-
Release the retaining clips (x2) that attach the LH 3rd row seat headrest to the seat
back.
Tip: Use of the following tool(s) is recommended:
- 6 in 90 degree tip miniature soft grip pick
-
Lift the LH 3rd row seat headrest upwards to remove the headrest from the seat frame,
and then remove the headrest from the vehicle.
Install
-
Position the LH 3rd row seat headrest
on the vehicle, and then feed the headrest actuator cable into the headrest guide
opening.
-
Install the retaining clips (x2) that attach the LH 3rd row seat headrest to the seat
back.
-
Install the LH 3rd row seat headrest
actuator cable on the actuator.
-
Install the LH 3rd row seat headrest
actuator cable to the cable tether mount.
-
Fold the seat upholstery and cushion assembly over the seat frame.
NoteUse the folding function to assist with tucking the upholstery.
-
Engage the J hook clip that attaches the upper half of LH 3rd row seat upholstery to
the seat.
NoteFold the seat to a workable position, start at one end of the J hook clip, and then fold the clip inwards until the other end of the upholstery is fully tucked.
-
Disconnect the LH 3rd row seat connectors (x2), and then route the connectors through
the seat upholstery.
-
Connect the LH 3rd row seat connectors (x2).
-
Engage the tabs (x4), fir tree clips (x2), and J hook that attach the lower section
of the LH 3rd row seat upholstery to the seat.
- Install the LH 3rd row seat back carpet. See Seat Back Carpet - 3rd Row - LH (Remove and Replace).
- Install the rear trunk carpet. See Carpet - Rear Trunk (5 Seat) (Remove and Replace).
- Install the rear trunk floor NVH insulator. See NVH Insulator - Floor - Rear Trunk (Remove and Replace).
- Install the rear trunk load floor. See Trunk Load Floor - Rear (Remove and Replace).
- Unfold the LH and RH 3rd row seats into original position.
- Close the liftgate.
- Unfold the 2nd row 40 and 60 seats into original position.
- Close the LH and RH falcon wing doors.