29/05/2024 18:08:41

Carpet - Sliding - Seat - 2nd Row - LH (Remove and Replace)

Correction code 153091120.45NOTE: See to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com.

Remove

  1. Open all four doors.
  2. Lower the LH and RH front windows.
  3. Connect toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  4. In Toolbox 3, click the Actions/Autodiag tab, and type "BCS2L" into the search field.
  5. Select PROC_BCREAR_X_SEAT-INSTALL-MODE-ONvia Toolbox: (link), click Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the routine is specific to "BCS2L", and then select ‘X’ at the upper right of the window to close after completion.
  6. Disconnect toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
  7. Move the LH and RH front seats forward.
  8. Remove the LH and RH rear sill panel trims. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  9. Remove the 2nd row floor mat. See Floor Mat - 2nd Row (Remove and Replace).
  10. Remove the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (6 Seat) (Remove and Replace).
  11. Remove the LH 2nd row seat post outer trim. See Trim - Outer - Seat Post - 2nd Row - LH (Remove and Replace).
  12. Remove the LH 2nd row seat post inner trim. See Trim - Inner - Seat Post - 2nd Row - LH (Remove and Replace).
  13. Move the 2nd row LH monopost seat fully backwards.
  14. Remove the LH 2nd row seat sliding plate. See Plate - Sliding - Seat - 2nd Row - LH (Remove and Replace).
  15. Remove and discard the LH 2nd row seat sliding carpet from the sliding plate. Use IPA wipes to remove remaining adhesive residue from the plate.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool

Install

  1. Install a new LH 2nd row seat sliding carpet on the sliding plate.
  2. Install the LH 2nd row seat sliding plate. See Plate - Sliding - Seat - 2nd Row - LH (Remove and Replace).
  3. Install the LH 2nd row seat post inner trim. See Trim - Inner - Seat Post - 2nd Row - LH (Remove and Replace).
  4. Install the LH 2nd row seat post outer trim. See Trim - Outer - Seat Post - 2nd Row - LH (Remove and Replace).
  5. Install the 2nd row mid floor panel. See Floor Panel - Mid - 2nd Row (6 Seat) (Remove and Replace).
  6. Install the 2nd row floor mat. See Floor Mat - 2nd Row (Remove and Replace).
  7. Install the LH and RH rear sill panel trims. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  8. Close the LH and RH falcon wings doors.
  9. Move the LH and RH front seats to original position.
  10. Reconnect toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  11. In Toolbox 3, click the Actions/Autodiag tab, and type "BCS2L" into the search field.
  12. Select PROC_BCREAR_X_SEAT-INSTALL-MODE-OFFvia Toolbox: (link), click Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the routine is specific to "BCS2L", and then select ‘X’ at the upper right of the window to close after completion.
  13. Disconnect toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
  14. Raise the LH and RH front windows.
  15. Close the LH and RH front doors.