01/07/2022 10:29:26

Striker - Door - Rear - LH (Remove and Replace)

Correction code 11354002 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open the LH and RH front doors.
  2. Lower the LH and RH front windows.
  3. Open the LH and RH falcon wing doors.
  4. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  5. Open the liftgate.
  6. Fold the LH 3rd row seat downward.
  7. Release the clips (x4) that attach the LH trunk sill side trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Plastic trim tool
  8. Remove the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  9. Remove the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  10. Release the clips (x10) that attach the lower portion of the LH rear racetrack trim to the vehicle, and then move the trim inward to gain access to the LH lower racetrack trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Plastic trim tool
  11. Remove the LH lower racetrack trim. See Racetrack Trim - Lower - LH (Remove and Replace).
  12. Remove the bolts (x2) that attach the LH rear door striker to the vehicle, and then remove the striker from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take note of the striker position with respect to the bolts in order to gauge proper fitment.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Torx T40 socket

Install

  1. Position the LH rear door striker on the vehicle, and then install the bolts (x2) that attach the striker to the vehicle.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • ¼ in to 3/8 in adapter
    • Ratchet/torque wrench
    • Torx T40 socket
  2. Install the LH lower racetrack trim. See Racetrack Trim - Lower - LH (Remove and Replace).
  3. Install the clips (x10) that attach the lower portion of the LH rear racetrack trim to the vehicle.
  4. Ensure that the falcon wing door seal is seated behind the LH rear racetrack trim.
  5. Install the LH lower C-pillar trim. See Trim - C-Pillar - Lower - LH (Remove and Replace).
  6. Install the LH mid C-pillar trim. See Trim - C-Pillar - Mid - LH (Remove and Replace).
  7. Install the clips (x4) that attach the LH trunk sill side trim to the vehicle.
  8. Move the LH 3rd row seat to original position.
  9. Close the liftgate.
  10. Install the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  11. Close the LH and RH falcon wing doors.
  12. Raise the LH and RH front windows.
  13. Close the LH and RH front doors.