2025-06-03

MXP3 ELECTRICAL - Wipers and Washers - Windshield Washer Bottle and Pump - Washer Pump (2025+) (RR)

Correction code NEW NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  • 2025-06-02: Released new procedure.
  1. Open the LH front door.
  2. Lower the LH front window.
  3. Raise and support the vehicle.
  4. Open the hood.
  5. Remove the LH front wheel center cap.
  6. Loosen LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Note
    5x nuts, 21mm, 175 Nm
  7. Raise vehicle partially and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Note
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  8. Remove the LH front wheel.
  9. Partially release rear edge of LH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  10. Release clips securing front portion of the LH front wheel house liner
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x push nut, Move aside for access
  11. Release clips securing rear portion of the LH front wheel house liner and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, 1x push nut
  12. Disconnect washer pump
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  13. Disconnect washer hose from washer pump
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose
  14. Disconnect fascia camera hose from washer pump
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose
  15. Remove washer pump from washer tank
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull washer pump straight up to remove it from washer bottle
  16. Install washer pump to washer tank
    Informational PurposesAn informational icon, calling your attention
    Note
    Fully seat pump to grommet and face hose coupling forward
  17. Connect washer hose to washer pump
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose
  18. Connect fascia camera hose to washer pump
    Informational PurposesAn informational icon, calling your attention
    Note
    1x hose
  19. Install LH front wheel house liner and secure rear portion of the wheel house liner to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, 1x push nut
  20. Install clips securing front portion of the LH front wheel house liner
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x push nut
  21. Secure partially released LH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  22. Install the LH front wheel.
  23. Lower vehicle until tires are touching ground
    Informational PurposesAn informational icon, calling your attention
    Note
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  24. Torque the LH front wheel lug nuts.
  25. Install the LH front wheel center cap.
  26. Fill washer fluid reservoir
    Informational PurposesAn informational icon, calling your attention
    Note
    Fill the reservoir until the fluid level is visible just below the filler neck
  27. Close the hood.
  28. Lower and remove the vehicle from the lift.
  29. Raise the LH front window.
  30. Close the LH front door.