18/05/2023 14:26:46

Horn - High Tone (Remove and Replace)

Correction code 17530102 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Open the LH front door.
  2. Lower the LH front window.
  3. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  4. Release the clips (x6) and push nut that partially attach the front portion of the LH front wheel house liner to the vehicle body, and then move the liner aside for access.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  5. Disconnect the low tone horn locking connector.
    Tip: Use of the following tool(s) is recommended:
    • Small flat head screwdriver
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the red locking tab.
  6. Disconnect the high tone horn locking connector.
    Tip: Use of the following tool(s) is recommended:
    • Small flat head screwdriver
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the red locking tab.
  7. Remove the nut that attaches the horn assembly to the vehicle body, and then remove the horn assembly from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  8. Remove the nut that attaches the high tone horn to the horn assembly bracket, and then remove the high tone horn from the bracket.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Adapter 1/4in Dr. to 1/4in Hex Bit Quick Change
    • Cordless 1/4in Hex Driver

Install

  1. Position the high tone horn on the horn assembly bracket, and then install the nut that attaches the high tone horn to the bracket.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Adapter 1/4in Dr. to 1/4in Hex Bit Quick Change
    • Cordless 1/4in Hex Driver
    • Torque wrench with angle measurement
  2. Position the horn assembly on the vehicle, and then install the nut that attaches the horn assembly to the vehicle body.
    12 Nm (8.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 2 in extension
    • 10 mm deep socket
    • Flex head ratchet/flex head torque wrench
  3. Connect the high tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the red locking tab is fully seated and engaged.
  4. Connect the low tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the red locking tab is fully seated and engaged.
  5. Install the clips (x6) and push nut that attach the front portion of the LH front wheel house liner to the vehicle body.
  6. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  7. Raise the LH front window.
  8. Close the LH front door.