01/11/2022 17:03:26

Bracket - Compressor - Air Suspension (Remove and Replace)

Correction code 31102012 1.14 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Remove the front fascia assembly. See Fascia Assembly - Front (Remove and Install).
  2. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Note
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  3. Release the clips (x2) that attach the electrical harness and air line bundle to the air compressor bracket.
  4. Release the locking tabs, and then disconnect the electrical harnesses (x2) from the air suspension compressor.
  5. Release the clip that attaches the intake valve to the vehicle.
    Tip: This valve is located slightly above the air suspension valve block.
  6. Remove the fastener assemblies (x3) that attach the air suspension compressor carrier bracket to the air suspension compressor bracket, and then support the compressor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    The air compressor will drop once the fasteners are removed. Support the compressor with hangers and bungee cords.
    Informational PurposesAn informational icon, calling your attention
    Note
    The fastener assemblies consist of the spring, spring seat, and isolator.
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    • 2 in extension
  7. Remove the bolts (x2) that attach the air suspension valve block to the air suspension compressor bracket.
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    • 6 in extension
  8. Remove and discard the nuts (x3) that attach the air suspension compressor bracket to the body.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • 6 in extension
  9. Carefully release the air compressor bracket from the vehicle, but do not fully remove the bracket, as an air hose is still attached to the bracket.
  10. Release the clip that attaches the air suspension intake hose to the air compressor bracket, and then remove the bracket from the vehicle.

Install

  1. Install the clip that attaches the air suspension intake hose to the air compressor bracket.
  2. Position the air compressor bracket on the vehicle.
  3. Install the new nuts (x3) that attach the air suspension compressor bracket to the body.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • 6 in extension
  4. Install the bolts (x2) that attach the air suspension valve block to the air suspension compressor bracket.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    • 6 in extension
  5. Remove the bungee cords from the air suspension compressor carrier bracket assembly, position the compressor carrier bracket assembly on the compressor bracket, and then install the fastener assemblies (x3) that attach the carrier bracket to the compressor bracket.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
    • 2 in extension
  6. Install the clip that attaches the intake valve to the vehicle.
  7. Connect the electrical harnesses (x2) to the air suspension compressor, making sure the locking tabs engage.
  8. Install the clips (x2) that attach the electrical harness and air line bundle to the air compressor bracket.
  9. Lower vehicle partially and set lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Note
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  10. Install the front fascia assembly. See Fascia Assembly - Front (Remove and Install).