17/06/2022 13:11:21

Switch - Back Rest and Cushion Adjust - Driver Seat (Remove and Replace)

Correction code 13015102 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Move the driver seat forward.
  2. Release the lock that attaches the LH front seat belt to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the lock mechanism counter clockwise to release the seat belt.
  3. Remove the screw that attaches the driver seat outboard side shield to the seat assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  4. Remove the driver seat cushion adjust button. See Button - Cushion Adjust - Driver Seat (Remove and Replace).
  5. Remove the driver seat recliner button. See Button - Recliner Adjust - Driver Seat (Remove and Replace).
  6. Carefully release the clips (x7) that attach the driver seat outboard side shield to the seat assembly, but do not fully remove the side shield from the seat assembly.
  7. Disconnect the electrical harness from the seat switch.
  8. Remove the screws (x3) that attach the back rest and cushion adjust switch to the driver seat outboard side shield, and then remove the switch from the side shield.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Do not remove the Philips head screws or damage may occur to the seat switch.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench

Install

  1. Position the back rest and cushion adjust switch onto the driver seat outboard side shield, and then install the screws (x3) that attach the switch to the side shield.
    1.7 Nm (1.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  2. Connect the electrical harness to the back rest and cushion adjust switch assembly, and then verify the functions of the seat switches.
  3. Position the driver seat outboard side shield onto the seat, and then install the clips (x7) that attach the side shield to the seat.
    Tip: Apply pressure to the side shield to fully seat the clips. The side shield should sit flush against the seat cushion.
  4. Install the driver seat recliner adjust button. See Button - Recliner Adjust - Driver Seat (Remove and Replace).
  5. Install the driver seat cushion adjust button. See Button - Cushion Adjust - Driver Seat (Remove and Replace).
  6. Install the screw that attaches the driver seat outboard side shield to the seat assembly.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  7. Position the LH front seat belt to the seat, and then engage the lock mechanism that attaches the LH front seat belt to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the lock clockwise to reattach the seat belt.
  8. Move the driver seat to the original position.