Hose - Outlet - Rear Drive Unit (Remove and Replace)
Correction code 18302502 2.94 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.
Remove
- Move the vehicle to a 2 post lift. See Raise Vehicle - 2 Post Lift.
- Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
- Release the electronic parking brake. See Park Brake Caliper - Release.
- Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
- Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Remove the underhood storage unit. See Underhood Storage Unit (Remove and Install).
- Disconnect LV power. See LV Power (Disconnect and Connect).
-
Set the high voltage multimeter to DC
voltage, lightly touch the probes to the auxiliary battery connector contacts, and
verify that the multimeter displays a voltage.
NoteBattery voltage is typically 14.5 to 15.5 volts.
- Remove the rear wheels. See Wheel Assembly (Remove and Install).
- Remove the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).
- Perform Vehicle HV Disablement Procedure. See Vehicle HV Disablement Procedure.
- Remove the leather glove protectors and HV insulating gloves.
- Remove the rear fascia diffuser. See Diffuser - Rear Fascia (Remove and Replace).
- Remove the nut that attaches the rear drive unit ground strap to the body stud, and then remove the ground strap from the stud.
- Remove the rear subframe assembly. See Subframe Assembly - Rear (Remove and Install).
- Remove the bolts (x4) that attach the rear subframe stiffener to the rear subframe, and then remove the stiffener from the subframe.
- Release the clip, disconnect the rear drive unit outlet hose from the rear drive unit heat exchanger, and then immediately plug the fittings.
- Release the clips (x5) that attach the rear drive unit outlet hose to the rear subframe assembly, and then remove the hose from the subframe assembly.
Install
- Install the rear drive unit outlet hose to the rear subframe assembly, and then fasten the clips (x5) that attach the hose to the subframe assembly.
- Remove the plugs from the fittings, immediately connect the rear drive unit outlet hose to the rear drive unit heat exchanger, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
-
Install the rear subframe stiffener to
the rear subframe, and then install the bolts (x4) that attach the stiffener to the
subframe.
- Install the rear subframe assembly. See Subframe Assembly - Rear (Remove and Install).
-
Install the rear drive unit ground
strap to the body stud, and then install the nut that attaches the ground strap to the
stud.
- Install the rear fascia diffuser. See Diffuser - Rear Fascia (Remove and Replace).
- Install the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).
- Install the rear wheels. See Wheel Assembly (Remove and Install).
- Connect LV power. See LV Power (Disconnect and Connect).
- Engage the electronic parking brake. See Park Brake Caliper - Release.
- Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
- Perform a cooling system air purge. See Cooling System (Partial Refill and Bleed).
- Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
- Install the underhood storage unit. See Underhood Storage Unit (Remove and Install).
- Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Hold the LH and RH B-pillar upper buttons in the Close position to manually calibrate the LH and RH falcon wing doors.
- Remove the vehicle from the 2 post lift. See Raise Vehicle - 2 Post Lift.
- Perform a four wheel alignment check, and adjust if necessary. See .