2026-08-09

Phone Dock - Center Console (Remove and Replace)

Correction code 15190012 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2026-03-10: Added the firmware reinstallation step.

Remove

  1. Open the RH front door and lower the RH front window.
  2. Pull upwards from the bottom of the center console phone dock assembly to release the clips (x4), and then swing the dock outward from under the instrument panel to release it from the center console.
  3. Release the connector locks, disconnect the electrical connectors (x3), release the clip that attaches the harness to the center console, and then remove the center console phone dock from the center console.
  4. Remove the screws (x3) that attach the inductive charge to the center console phone dock assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  5. Release the tabs (x2) at the top of the center console phone dock assembly, angle the inductive charger up and slide it outward to remove it from the dock assembly.
  6. Remove the screws (x5) that attach the hazard button to the phone dock.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  7. Release the clips (x3) that attach the hazard button to the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the clips, and then rotate out of the phone dock.

Install

  1. Fasten the clips (x3) that attach the hazard button to the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the hazard button into the phone dock by aligning the datums, and then fasten the clips (x3).
  2. Install the screws (x5) that attach the hazard button to the phone dock.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Inspect the front of the phone dock to ensure that the hazard button module is flush to the phone dock.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  3. Position the inductive charger into the center console phone dock assembly, and then secure the tabs (x2) that attach the charger to the assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the inductive charger datums into the phone dock assembly before fully engaging the tabs.
  4. Install the screws (x3) that attach the inductive charge to the center console phone dock assembly.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  5. Position the center console phone dock assembly into the vehicle, connect the electrical connectors (x3), secure the connector locks, and then secure the clip that attaches the harness to the center console.
  6. Position the center console phone dock into the center console, and then secure the tabs (x4) that attach the assembly to the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the datums forward into the IP and secure tabs down into center console
  7. Reinstall the vehicle firmware. See Firmware Reinstall - Touchscreen.
  8. Raise the RH front window and close the RH front door.