17/06/2022 13:20:04

Center Console Assembly (Remove and Replace)

Correction code 15192402 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Release console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 7x datums, Disengage bottom clips last and pull rearward due to alignment
  2. Remove console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Connector lock for lamp located underneath bracket
  3. Release LH and RH rear console carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  4. Move RH front seat backward
  5. Move LH front seat backward
  6. Release phone dock
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 2x datums, Pull up at bottom and swing out from under instrument panel
  7. Remove phone dock
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 1x clip, Take caution to release connector locks before pulling straight out of each socket to avoid damage
  8. Release IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    4x tabs, 2x datums
  9. Release diagnostic and CAN harnesses from IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  10. Remove IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  11. Remove LH outboard footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x magnets, 2x datums
  12. Remove LH inboard footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cover, 1x clip, 1x datum, 1x screw, 8 mm, 1 Nm
  13. Remove LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  14. Release LH center console lower bracket from IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  15. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 1x connector, 4x datums
  16. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  17. Release RH center console lower bracket from IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  18. Release center console connectors to body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors
  19. Release console carrier center bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  20. Recline LH front seat backrest
  21. Recline RH front seat backrest
  22. Remove console assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift at rear, rotate front from under IP and out passenger door, Take care not to scratch seats, IP or inner door panel, Recommend assistance if needed
  23. Install console assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully maneuver front of assembly under and into IP carrier and lower rear into place, Recommend assistance if needed
  24. Secure LH center console lower bracket to IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  25. Secure RH center console lower bracket to IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 10 Nm
  26. Secure center console connectors to body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors, Ensure all connector locks engage
  27. Secure console carrier center bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  28. Install RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  29. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    3x magnets, 4x datums, 1x connector
  30. Install LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  31. Install LH inboard footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x cover, 1x clip, 1x datum, 1x screw, 8 mm, 1 Nm, Align datums and footwell vent before installing screw
  32. Install LH outboard footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x magnets, 2x datums
  33. Secure diagnostic and CAN harnesses to IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  34. Install IP service panel
    Informational PurposesAn informational icon, calling your attention
    Note
    4x tabs, 2 datums
  35. Install phone dock connections
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 1x clip
  36. Install phone dock
    Informational PurposesAn informational icon, calling your attention
    Note
    2x datums, 4 tabs, Slide datums forward into IP and secure tabs down into center console
  37. Raise LH front seat backrest
  38. Raise RH front seat backrest
  39. Secure LH and RH rear console carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 12 Nm
  40. Install console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  41. Secure console back panel assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 7x datums, Engage bottom clips first due to forward facing alignment