07/07/2022 14:32:48

Light - Map - Front (Remove and Replace)

Correction code 17350312 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open all the doors and lower the front windows.
  2. Remove the LH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  3. Remove the bolts (x2) that attach the LH upper A-pillar trim to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 13mm socket
  4. Remove the screw that attaches the LH upper A-pillar trim to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  5. Move the LH upper A-pillar aside to access the headliner.
  6. Remove the screw that attaches the front of the headliner to the body.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  7. Remove the LH lower B-pillar trim. See .
  8. Release the clips (x3) and magnets (x2) that attach the LH upper B-pillar trim to the B-pillar, and then disconnect the LH falcon wing door button electrical connector.
  9. Move the LH upper B-pillar trim aside.
  10. Release the clips (x5) that attach the LH front portion of the headliner to the vehicle, and then partially release the headliner.
  11. Disconnect the front map light electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take note of any NVH mitigation present.
  12. Release the clips (x4) that attach the front map light to the headliner, and then remove the light from the headliner.

Install

  1. Position the front map light into the headliner, and then secure the clips (x4) that attach the light to the headliner.
  2. Connect the front map light electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure any noted NVH mitigation.
  3. Make sure the LH falcon door seal is seated behind the B-pillar racetrack.
  4. Secure the clips (x5) that attach the LH front portion of the headliner to the vehicle.
  5. Install the screw that attaches the front of the headliner to the body.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  6. Connect the LH falcon wing door button electrical connector, and then secure the clips (x3) and magnets (x2) that attach the LH upper B-pillar trim to the B-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any damaged clips.
  7. Install the LH lower B-pillar trim. See .
  8. Position the LH upper A-pillar onto the A-pillar.
  9. Install a new nut that attaches the LH upper A-pillar trim to the vehicle.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  10. Install the screw that attaches the LH upper A-pillar trim to the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • T20 socket
  11. Install the LH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  12. Move driver seat to the original position.
  13. Raise the front windows and close all the doors.