24/05/2023 04:32:03

Door Glass - Rear - LH (Adjust)

Correction code 11500300 0.70 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-05-24: Added cleaning instructions to prevent glass damage.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Lower LH rear window
  2. Open LH rear door partially
  3. Remove LH rear outer belt trim
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift and roll outward slowly and evenly starting from the rear edge, Careful not to bend or damage components
  4. Open LH falcon wing door
  5. Remove LH falcon door lower garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    9x V-clips, Replace any damaged or missing V-clips, Take care not to damage door trim panel during removal
  6. Remove LH décor trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, 2x connectors
  7. Remove LH door panel bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, 10mm, 6 Nm
  8. Remove LH door trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    13x clips, 2x connectors
  9. Set LH Falcon door at a comfortable working height
  10. Open hood
    Informational PurposesAn informational icon, calling your attention
    Note
    Via center display > Controls > Frunk Open
  11. Power off vehicle via center display
    Informational PurposesAn informational icon, calling your attention
    Note
    Controls > Safety & Security > Power Off
  12. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  13. Disconnect LV battery connector and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL
  14. Remove LH rear door inner belt seal
  15. Disconnect LH falcon door air bag connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Release orange lock and then disconnect
  16. Remove screws securing LH closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    10x bolts, T25, 1.8 Nm
  17. Remove screws securing window motor to the LH closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x screws, T30, 1.8 Nm
  18. Pull LH closeout panel away from door and lift window motor up to release
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  19. Disconnect falcon door protection ECU
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Release black locking tab
  20. Disconnect connectors from falcon door module
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  21. Release clips securing harnesses and connectors to the LH closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  22. Unclip and feed door release cable through LH closeout panel
  23. Loosen nut securing the front of the window to the regulator
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 10mm, 9 Nm, Nut does not need to be fully removed, If required power the vehicle back on and use the window switch tool to move regulator for nut access
  24. Inspect the regulator for glass splinters or other debris, and clean it if necessary.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Debris and splinters may damage or shatter the new door glass.
  25. Partially close LH rear door
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not engage latch
  26. Check window fitment, adjust as needed
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to CVIS for latest specifications https://service.teslamotors.com/protected-doc/ModelS/TheoryOp/InspectionStandards/index_frames.html
  27. Verify window glass fitment and tighten nut securing the front of the window to the regulator
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 10mm, 9 Nm,
  28. Install release cable through the LH closeout panel
  29. Secure window motor onto the back of the closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x tabs
  30. Install screws securing window motor to LH closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x screws, T30, 1.8 Nm
  31. Install LH closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    10x bolts, T25, 1.8 Nm
  32. Connect falcon door protection ECU
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, securing locking tab
  33. Connect LH falcon door air bag connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Engage locking tab
  34. Connect LH falcon door module
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  35. Install clips securing harnesses and connectors to closeout panel
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  36. Install LH rear inner belt seal
  37. Manually partially close LH rear door
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not engage latch
  38. Install LH rear door outer belt trim
  39. Connect First Responder Loop and LV battery connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage upper locking tab when fully seated
  40. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Note
    11x clips, 2x datums
  41. Close hood
  42. Raise LH rear window
  43. Test window function and check window fitment, adjust as needed
    Informational PurposesAn informational icon, calling your attention
    Note
    Refer to CVIS for latest specifications https://service.teslamotors.com/protected-doc/ModelS/TheoryOp/InspectionStandards/index_frames.html
  44. Install LH rear door trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, 13 clips, replace all clips, Install door trim starting from top and make sure the door trim tap is fitted correctly on the inner belt seal
  45. Install LH rear door trim bolts securing door trim panel to door
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, 10mm, 6 Nm
  46. Install LH rear door décor trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, 2x connectors, Take care not to damage door trim panel
  47. Install LH rear lower door garnish
    Informational PurposesAn informational icon, calling your attention
    Note
    9x V-clips
  48. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.