19/06/2023 14:00:34

Seat Assembly - 1st Row - LH (Remove and Install)

Correction code 13040101 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-06-19: Updated seat belt linkage release and install steps.

Remove

  1. Move the 1st row LH seat forward.
  2. Use a flathead screwdriver to rotate the lock mechanism on the front seat belt linkage counterclockwise to release it from the pretensioner, and then slide the linkage off the pretensioner and set it aside.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT rotate clockwise to avoid damage to the mechanism.
    Informational PurposesAn informational icon, calling your attention
    Note
    The linkage design may vary, but will function the same.
    Informational PurposesAn informational icon, calling your attention
    Note
    The lock screw will remain in the horizontal position when released.
    Informational PurposesAn informational icon, calling your attention
    Note
    A light audible click will be heard when the linkage is released.
  3. Open the LH falcon wing door.
  4. Remove and discard the bolts (x2) that attach the rear of the 1st row LH seat tracks to the vehicle.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  5. Move the 1st row LH seat rearward.
  6. Remove and discard the bolts (x2) that attach the front of the 1st row LH seat tracks to the vehicle.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  7. Move the 1st row LH seat to the middle of the track and the seat back to the most upright position.
  8. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Disconnect LV power. See LV Power (Disconnect and Connect).
  10. Position the 1st row LH seat to gain access to the underside of the seat.
  11. Release the clip that attaches the LH side body harness to the seat assembly, and then release the connector lock and disconnect the LH side body harness electrical connectors (x2) from the seat controller.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the red locking tab on the black connector before disconnecting the connector.
  12. With assistance, remove the 1st row LH seat from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the surrounding components.

Install

  1. With assistance, position the 1st row LH seat into the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the surrounding components while lifting the seat into the vehicle.
  2. Secure the clip that attaches the LH side body harness to the seat assembly, connect the LH side body harness electrical connectors (x2) to the seat controller, and then secure the connector lock.
  3. With assistance, move the 1st row LH seat to the upright position.
  4. Connect LV power. See LV Power (Disconnect and Connect).
  5. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  6. Calibrate the LH and RH falcon wing doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    Hold the upper B-pillar button in the down position to manually calibrate.
  7. Move the 1st row LH seat forward.
  8. Install the front seat belt linkage to the pretensioner:
    1. Make sure the lock screw is in the horizontal position. If the lock screw is not in the horizontal position, follow the release instructions to unlock it.
    2. Verify there are no twists in the seat belt from the upper B-pillar trim to the pretensioner.
    3. Install the linkage onto the pretensioner cable.
      Informational PurposesAn informational icon, calling your attention
      Note
      An audible click will be heard.
      Informational PurposesAn informational icon, calling your attention
      Note
      The lock screw will rotate back to the locked position.
    4. Perform a firm pull test on the seat belt with at least 15 pounds of force.
  9. Install new bolts (x2) that attach the rear of the 1st row LH seat tracks to the vehicle.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  10. Move the 1st row RH seat rearward.
  11. Install new bolts (x2) that attach the front of the 1st row LH seat tracks to the vehicle.
    34 Nm (25.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
  12. Move the 1st row LH seat to the original position.