01/04/2024 14:01:38

Drive Shaft - 2nd Row Seat Motor - LH (6 Seat) (Remove and Replace)

Correction code 13025002 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Open all the doors and lower the front windows.
  2. Move the driver seat forward.
  3. Remove the LH 2nd row seat underbelly trim. See Trim - Underbelly - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
  4. Remove the metal push nut and spacer that secure the LH 2nd row seat motor drive shaft to the pitch motor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Work the nut from each side to remove it. Apply pressure to the top of strut rod to move it downward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Discard the metal push nut after removal.
  5. Move the LH 2nd row seat motor drive shaft away from the pitch motor until the lower fan nut is touching the pitch gearbox.
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply pressure to the top of the drive shaft to it move downward.
  6. Remove the lower metal push nut and spacer that secure the LH seat motor 2nd row seat motor drive shaft to the pitch motor, and then remove the drive shaft from the pitch motor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Work nut from each side to remove it from the pitch motor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Discard the metal push nut after removal.

Install

  1. Position the LH 2nd row seat motor drive shaft into the vehicle, and then install the washer and new metal push nut onto the drive shaft.
  2. Slide the LH 2nd row seat motor drive shaft through the pitch motor, and then install the washer and new metal push nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install the spacer then new push nut after the drive shaft has been pushed through the motor.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a clip prytool to push against the nut while applying pressure to the bottom side of drive shaft.
  3. Install the LH 2nd row seat underbelly trim. See Trim - Underbelly - 2nd Row Seat - LH (6 Seat) (Remove and Replace).
  4. Move the driver seat to the original position.
  5. Connect a laptop with Toolbox 3 to the vehicle.
  6. In Toolbox, click the Actions tab, and then search for "BCS2L".
  7. Click PROC_BCS2L_R2-L_CALIBRATE-S2L-PITCHvia Toolbox: (link), and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click the X at the top right corner of the window to close once complete.
  8. Click PROC_BCS2L_R2-L_CALIBRATE-S2L-TRACKvia Toolbox: (link), and then click Run and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Click the X at the top right corner of the window to close once complete.
  9. Disconnect Toolbox and remove the laptop from the vehicle.
  10. Close the LH front door.