08/09/2022 16:26:11

Knee Airbag - Front Passenger (Remove and Replace)

Correction code 20010402 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

Remove

  1. Remove the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  2. Remove the RH center console side panel. See Side Panel - Center Console - LH (Remove and Replace).
  3. Remove the RH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  4. Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  5. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  6. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  7. Disconnect LV power. See LV Power (Disconnect and Connect).
  8. Remove the bolts (x2) and clip that attach the front passenger knee airbag assembly to the vehicle.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  9. Release the tabs (x6) and clip that attach the front passenger knee airbag assembly to the vehicle, disconnect the electrical connectors (x2), and then remove the assembly from the vehicle.
  10. Remove and discard the bolts (x2) that attach the front passenger knee airbag cover brace to the airbag assembly, and then remove the brace from the assembly.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • E10 socket
  11. Remove and discard the bolts (x4) that attach the front passenger knee airbag cover to the front passenger knee airbag, release the tabs (x5), and then rotate the airbag out of the cover to remove it.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • E10 socket

Install

  1. Position the front passenger knee airbag into the front passenger knee airbag cover, secure the tabs (x5), and then install new bolts (x4) that attach the cover to the airbag.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Rotate the airbag into the cover.
    Tip: Use of the following tool(s) is recommended:
    • E10 socket
  2. Position the front passenger knee airbag cover brace into the airbag assembly, and then install new bolts (x2) that attach the brace to the assembly.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • E10 socket
  3. Position the front passenger knee airbag assembly into the vehicle, connect the electrical connectors (x2), and then secure the tabs (x6) and clip that attach the assembly to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Support the assembly while connecting the connectors.
    Informational PurposesAn informational icon, calling your attention
    Note
    Hook tabs before fully seating the assembly,
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to damage the connectors and harness.
  4. Install the bolts (x2) and clip that attach the front passenger knee airbag assembly to the vehicle.
    8 Nm (5.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10mm socket
  5. Install the RH center console side panel. See Side Panel - Center Console - LH (Remove and Replace).
  6. Install the passenger footwell cover. See Cover - Footwell - Passenger (Remove and Replace).
  7. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  8. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  9. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  10. Install the RH front sill panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  11. Install the RH front floor mat.
  12. Connect LV power. See LV Power (Disconnect and Connect).
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  14. Calibrate the rear doors.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors