03/10/2024 13:10:47

Firmware Reinstall - Toolbox

Correction code 00020008 0.05 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2023-07-24: Updated LV maintainer guidance.
Informational PurposesAn informational icon, calling your attention
Note
This procedure describes how to reinstall the currently installed software using a laptop with Toolbox 3 locally connected. The package will not be downloaded from Tesla servers.

Software Reinstall

  1. Connect the LV maintainer to the vehicle, but do not disconnect the LV battery. See LV Maintainer (Connect and Disconnect).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is OK for the LV maintainer and LV battery to both be connected while performing this procedure.
  2. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
    Informational PurposesAn informational icon, calling your attention
    Note
    Locally connecting the vehicle to Toolbox 3 will automatically enable Service Mode Plus.
  3. In Toolbox, select the Actions/Autodiag tab, and then search for "redeploy".
  4. Run the UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    routine and wait for the reinstallation to complete. Reinstallation status can be monitored on the vehicle touchscreen.
    Tip: UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    is a "partial" software reinstallation that reinstalls the currently installed software package to all module, ECU, and component replacements, with the exception of the car computer.
  5. Once the reinstallation is complete, check that the release notes appear on the touchscreen, indicating a successful reinstallation.
  6. Disconnect the LV maintainer from the vehicle. See LV Maintainer (Connect and Disconnect).
  7. Disconnect the laptop from the vehicle. See Toolbox 3 (Connect and Disconnect).
  8. Disable Service Mode. See Service Mode (Enable and Disable).
  9. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).