2026-06-19

Perform General Inspection (Inspection)

Correction code 00030700 FRT 1.14 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

2026-06-18: Released new procedure.

Procedure

Function check LH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Function check all windows from the master switch

Note
Check operation with door closed, Document any abnormal operation/noises
Function check LH rear door (exterior)

Note
Inspect and note functionality for the door handle operation, and full range of motion of the door, From outside look for interference with brightwork and door to body, Function test closing button on door, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH rear door (exterior)

Note
Inspect and note functionality for the door handle operation, and full range of motion of the door, From outside look for interference with brightwork and door to body, Function test closing button on door, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Function check the exterior lights

Note
Recommend assistance, Check headlamps, fog lights, license plate, tail, brake, reverse, and side repeaters
Engage drive rails and activate windshield washer and wiper operation

Note
Engage drive rails and hold down on the washer button, Verify wipers and washer is operating as intended
Function check horn
Open the hood.
Remove the rear underhood apron.
Remove the RH underhood apron.
Remove the LH underhood apron.
Remove the front underhood apron.
Remove the underhood storage unit access panel.
Remove the underhood storage unit carpet.
Remove the underhood storage unit from the vehicle.
Perform inspection of under hood area

Note
Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect brake fluid level
Inspect coolant level and top off as necessary

Note
Ensure that the fluid level is at the Max line, Top off fluid as required
Fill washer fluid reservoir

Note
Fill the reservoir until the fluid level is visible just below the filler neck
Raise and support the vehicle.
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove push clips securing front aero shield

Note
5x push clips
Remove bolts securing front aero shield and remove from vehicle

Note
9x bolts, 10mm, 6 Nm
Release mid aero shield

Note
4x push clips
Remove mid aero shield

Note
16x bolts, 10mm, 6 Nm
Check tire pressures

Note
4x tires, Adjust to specification if necessary
Measure and record RH front tread depth

Note
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Measure and record RH front brake pad thickness
Inspect RH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 30mm
Measure and record RH rear tread depth

Note
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Measure and record RH rear brake pad thickness

Note
Add line to replace if under 5mm
Inspect RH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 26mm
Measure and record LH rear tread depth

Note
Record at least 3 measurements: Inner, Middle, Add line to replace if under 5/32 inch tread remaining
Measure and record LH rear brake pad thickness
Inspect LH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 26mm
Measure and record LH front tread depth

Note
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Measure and record LH front brake pad thickness

Note
Add line to replace if under 5mm
Inspect LH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 30mm
Perform inspection of vehicle underside components front and rear

Note
Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect underside of vehicle for fluid leaks
Perform inspection of steering components

Note
Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
Perform inspection of suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of front suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of rear suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Inspect underside of battery for damage
Install mid aero shield

Note
16x bolts, 10mm, 6 Nm, Apply Loctite 222 onto mid aero shield bolts and install fasteners securing mid aero shield to vehicle
Position mid aero shield

Note
4x push clips
Apply Loctite 222 onto front aero shield bolts and secure front aero shield to vehicle

Note
9x bolts, 10mm, 6 Nm
Install push clips securing front aero shield

Note
5x push clips
Lower vehicle fully

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Lower and remove the vehicle from the lift.
Install the underhood storage unit.
Install the underhood storage unit carpet.
Install the underhood storage unit access panel.
Install the front underhood apron.
Install the LH underhood apron.
Install the RH underhood apron.
Install the rear underhood apron.
Close the hood.
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance

Note
The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
Inspect vehicles alignment

Note
Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction

Model X Service Manual

Perform General Inspection (Inspection)

Procedure

Figure 1

Figure 2

Figure 3